GSQ9611KT2 Whirlpool Washer - Instructions

First off I would highly recommend the review by Dennis From Evans City PA. This was quite helpful.

The problem is the lid switch assembly is glued together and the original part came apart and needed to be replaced. The symptoms described by others were accurate so we opted to replace it.

On my machine there are two screw on the front corners of the panel where the dials attach to the top of the washing machine. I removed those two screws and by lifting up and forward was able to move the whole thing out of the way.

You should see the connection from the dial panel running down into the wash basin. This is where you will unplug the old switch and replace it with a new one. There are little plastic clips that hold it in place, but you can squeeze them with your fingers to remove it from the panel.

In order to get access to the underside where the wires are connected you will need to remove two clips that hold the back pane to the rest of the sheet metal. In my case I wasn't quite prepared for the entire frame to move but once the clips are removed the back panel is completely removed and you can pull it forward to gain access to the underside.

Once you are able to get underneath you will see a screw that holds the ground wire. This is the one that you may need pliers to remove. There are two screws that hold the switch in place but you can access them at any time. I had already removed the old screws by this point. This should leave the switch disconnected from everything and you can install the new one.

Now just connect everything back together. The two screws for switch where the lid hits. Connect the ground wire and run the the connection back to the top portion where it will connect back up to the top panel.

I would add that there are two thin plastic strips that ran vertically up the back fo the back panel that meet the outer casing. I had to re-seat these before putting the clips back on the top.

Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remove black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...

Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.

Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.

Removed bolt in center of agitator then slid agitator straight up and out replaced the dogs and the other parts that came with the cam kit i also replaced a few of the other parts that wear in the agitator ,you can actually re-cut the teeth on the dogs with a razor so that they will work again ,but new parts are very reasonably priced and the parts arrived very quickly the next day .

First I watched the "how to video" that corresponds with the part I ordered on the Parts Select web site. The instructions given in the video were so clear and complete that the job was incredibly easy. Parts Select makes appliance repair so easy that Im willing to bet that even the "May Tag" repair man becomes more lonely

took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.

Removed old part; exchanged rubber plungers between the hot and cold. Symptoms still the same - so eliminated the need for new rubber plungers (even though they still needed to be replaced). The only item left were the magnetic switches opening and closing the flows. The syphon was replaced due to broken plastic mountings causing the syphon to hang into the drum. Repair was a snap and finding the parts on your site was very easy and parts were there within 2 days at standard shipping. Thank you.

i knew the lid sw. must be bad and had a new one in hand, but when i remove the sw. ( near the lid ) i found the wires going back to where i could not reach. was not sure how to get at them so i repaired the sw. with tape untill i could find how to get at the wire end. after reading more in this repair area i know that i need to remove the control panel which is easy to do. next time i will read all i can on repairs in this section!!

first I removed the fabric softner and water seal from center of agitator, then I removed the bolt holding it on. All I had to do then is install new agitator with old bolt place water seal and fabric softner container back on and start washing clothes again. Very simple.

First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.

I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.

The repair was very easy. The only hard part was due to the age of the machine the cap covering the agitator assembly was stuck on the top.I had to use a very large pipe wrench to loosen it. Other than that the whole repair went very smooth. You will need an extension with the socket wrench in order to reach the screw holding down the agitator.I was very impressed with the service from Parts Select. I received my part very fast and it included everything I needed to complete the job.

Unscrewed the two screws that hold the water lines to the valve. Unscrewed and lifted the control panel, popped the two spring clips that hold the back panel against the housing. Pulled the valve just outside the back panel. Took off the internal water line and moved it over to the new valve. Took off both hot and bold electric plugs and moved them to the new valve. With the old valve off, I sled the new valve into place and screwed it to the back panel. Put the spring tabs back on the back panel and screwed the back panel back together. Plugged it in, attached the water supply lines and tested it. Worked fine.

we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!