GSQ9611KT2 Whirlpool Washer - Instructions

Replaced pump without disassembling the cabinet or disconnecting motor or any other parts.

Disconnected power, drain, hot and cold water lines. drained lines to pail before taping to top of unit.

Tipped the unit to a 45 Deg. angle, leaning the top side edge onto a stool so that pump presented well at the raised bottom edge.

Removed hose clamps at pump suction and discharge ports and drained water into a shallow soaking pan. Kept clamps on hoses to facilitate reinstallation of pump.

Removed spring clamps at front and rear of pump housing.

Wiggled motor shaft away from coupling in pump. This is a friction fit, so no parts removal was required and no parts "come loose" in the process.

Wiggled new pump housing onto the motor shaft after checking square shaft alignment with respect to square female coupling on pump.

Pushed and twisted hose ends onto pump suction and discharge ports, then pulled spring clamps down over hose ends at pump ports.

Reset spring clamps so that they were aligned and square with pump ports. Reconnected power, drain, hot and cold water line connections.

Washer ran as before but without leaks this time.

The tub was out of alignment and water fell behind it and onto the floor. My brother-in-law suggested my problem could be the tub balancing spring and when I moved my washing machine, there it was on the ground.
The schematic does not show where it hooks up. So after I did what I thought looked right, the machine still did not work properly. Then I replaced the three suspension springs and that didn't solve the problem.
I found a whirlpool "do-it-yourself" repair book at the library and was prepared to tear into the machine. However, I did not have the tub balancing spring in the correct spot at one end. It hooks up from one of the outer bracket to the back of the housing unit along between the legs. There is a hole that had rusted through. I simply drilled a new hole nearby and low and behold it works!
Easy fix - the frustration was with the poor schematic.

Removed top cap and one nut from agirtator then removed complete assembly. Replaced new assembly nut and cap.

I'd noticed for a while that our 15-year-old Kenmore washer was filling slowly, but when it started to take 30 minutes to fill to the "medium" level, I knew something was really wrong. There was plenty of water pressure, so I replaced a hose that was loaded with minerals and cleaned the filter (also clogged with minerals). But that didn't help! So I ordered a new water inlet valve, and replaced that. There's nothing tricky about the repair -- the hardest part is opening and closing the washer, for which I found instructions online. (Even so, it's the most time-consuming part of the project.) The result is the washer now fills as fast as when it was new. Just for fun, I took apart the old valve and expected to find it encrusted with minerals, but it looked fine, so I'm not sure where the actual breakdown was. But since the part only cost $25 -- less than a service call, for sure -- I was very happy to use a half hour of my time and keep the machine going a while longer.

Repair was simple, after finding the correct part from Partselect. Exact match. Old part out with removal of one bolt, new agitator assembly installed in five minutes. Works great and saved me from buying a new washer. Cost of repair about $80.00, replace washing machine, about $600.00.

The repair was very easy. The original dial was a poor design and did not hold up to the twisting and finally let loose. The threaded bottom of the dial stayed on the threaded shaft, so it was a simple matter of grabbing it with nose pliers and spinning off. Glue does not work with this type of plastic, I tried instant glue and hot glue. The replacement part was re-designed with a metal threaded center, so when it arrived in the mail, 3 days after online ordering, I spun it onto the shaft and job was complete. While I waited for the new part to arrive, I threaded 2 nuts onto the shaft and tightened them to each other to give me a temporary 'knob' that I could grab with my nose pliers.

Unbalanced load was creating a knocking sound (as if the clothes load was unbalanced). Dismantled the washer to find that one brackets had rusted out. [FYI: 3 bracket at 120 degree apart (for the 360 degree circle)]. I found that the hole (on the bracket) where the spring holds was gone. Purchased parts. Replaced them (spring, bracket, screw). Reassembled washer then ran wash for a cycle. Successful fix.

This is a machine I bought from Costco in 2001 - it has been very reliable and this was its first repair.
Getting the top off this washer requires a lot of disassembly. However, if you push the drum down on the right hand side of the machine, you can easily reach under the lid and remove the old switch. Mine had broken loose from its plastic mounts, so the lid plunger no longer activated it. Save the two screws that go through the washer top to secure the new switch.
I unplugged the electricity, reached under the top and pulled the old switch out. Its cables are enclosed in a stiff plastic hose with a slit down its length so you can pull the wires through the slit. You need to pull out around 6 inches of the wires. I then cut the wires to remove the old switch and next cut the wires on the new switch to the same length as the ones removed. Stagger the cuts about 1 inch so that the two joints will not be on top of each other. I stripped each end of the two wires, slipped shrink-wrap tubing (from radio shack) on to the new switch wires, then soldered the new switch wires to the existing wires back to the control center. I then slipped the shrink wrap over the soldered joints and shrank it with a match. Feed the joined wires back into the plastic tube and feed the switch under the washing machine rim. It takes a little maneuvering to get the switch aligned with the two screw holes in the top. Be sure the switch is pushed up into the lip opposite the screw holes - push the back end of the switch up into the lip before trying to align the front end of the switch with the screw holes. Align the screw holes with the switch holes, install the two screws and check that you hear the slight click of the microswitch if you push down a pencil into the interlock slot before you tighten everything up. Plug in the electricity and off you go!

Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, then used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.

Unplugged power cord and disconnected water lines; note which is hot/cold. Washer was then tipped on its front. Discharge hose was disconnected. Washer was then rolled over onto its back as this would put the pump on top for much easier removal.

Pried off two clips attaching pump on motor using a flathead screwdriver. The rear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.

Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.

Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.

Replaced clips to hold motor on transmission and reinstalled screws holding clips.

IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!

Attach pump onto motor and replace clips. Double check everything is back in place.

Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.

First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.

Washer is 29 years old. Found that tub spring hooks into a simple (non-reinforced) hole in the base frame, and it had worn the hole through through the edge of the frame (key hole style). Due to age and low cost of parts, ordered all suspension springs, brackets, & pads. Once they arrived, took the tubs out (first time for that), found that the suspension pads looked fine, but the wear pads showed a lot of wear and the front one was snapped in the middle, perhaps an after effect of the spring failure. From my lack of attention, initially tried to get front pad into the wrong set of holes, a bad fit; corrected. Simply drilled a near-by hole in the base frame for the tub spring.

While the tubs were out, took them outside and scrubbed them clean. Also cleaned agitator parts using bottle brushes. Followed the PartSelect videos and owner comments for procedures, methods. Found that some miss some important info, but if you watch others you can combine the info to find what you need re disassembly/assembly.

At one point while attempting to remove the outer tub, did not realize that the screw that holds the rear spring bracket to the tub also holds the tub to the suspension plate.

Took me most of a day for the whole process, and I ended up with pulled/spasmic muscles from all the bending over, mostly from cleaning parts I think. Very helpful to have the parts breakout drawings, videos, others' experience.

Removed back panel to remove tub from shell. Unscrewed the brackets holding the springs. Used screw driver to pop out pads with hammer onto screw driver. Cleaned out tub and put grease on springs where they attach to bracket. Replaced panel and ran machine to find a leak. Took machine apart again to find the knocking of the tub against the back panel caused a whole in the plastic tub. Silicon and mechanical tape. Washer works fine for now.

I ordered the parts at a minimal cost compared to the repairman's quote, they arrived in 3 days. I used the laptop and put it right next to where I was working so that I could follow the directions step-by-step. The instructions were easy to follow and showed you right what to do so I never had any questions. My washer had a slightly different configuration but I figured it out. Replacing the parts was simple, take one off, put the other on. Putting the washer front back on was a little tricky, I had to have my daughter help me hold it in place while I wiggled it around to make sure it was just right before I screwed it back together. It was easier than I thought it would be. I told my husband I loved the internet, I would never have been able to do this job without the instructional video. Thanks PartsSelect!

Turned off water and pulled power plug, Then unscrewed hot and cold hoses from washer.
I took off the top control by undoing the 2 screws in front and then the two screws on the back plastic latches. Mover it forware and took off the 2 screws on the bottom of the back which came up and off easily. Undid the two screws holding the Water valve to the back and undid the water outlet tube and the wireing. Replaced with new valve and reattached tubing and wires. Screwed back on and reattached controls.
Actually was very easy even without repair manual to the washing machine.

I had to take the motor and transmission out. They are one piece. Removed the clutch, take off trans. cover, remove a snap ring, take the striped gear off, and put the new one on. Then put put everything back on the way it came off.