GSE20IBTNFBB General Electric Refrigerator - Instructions

Connected the 2 wires and pushed in the switch until it clicked.

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

took the old one out and replaced it with the new one, then trashed the old one

Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.

Used small screw driver to pry the top of the switch away from left inside wall of freezer side of side-by-side refrig./freezer; then used pliers to remove the switch; then removed the 3 prong socket and plugged it to new switch and installed it into the inside wall of the freezer.

My son replaced both temperature sensors and the fridge works great now!!! Like brand new again!!!!

The repair is a snap, you can watch the video and it will put you on the right path. My story is more about the service that Part Select gave me. I used a small box fan on low as a temporary fix. My model number was worn off from the box wine we store in that particular place. So I ordered the part based on looks, well it was wrong. Called Part Select and we talked, the nice lady on the other end said OH it must be this fan motor. Send us back that one, and I'll get this out too you. I'll credit your account for $7.99, and it cost me $8.99 to ship back the wrong part. Wow, the next day I received the new motor. They sent it overnight! I thought it would be 5-6 days! Unbelievable. I will use this company for any, and all my repairs.

followed part select video instructions

What an awesome site! After putting in my model number and finding the problem I was having, I simply picked the 2 parts that were most likely to solve the problem. I bought a defrost thermostat, and defrost heater. To a high certainty, they would solve my problem. They didn't however! I ended up having to buy a temperature sensor on another order a few weeks later when the problem resurfaced! My own fault. I should have bought it the first time. As others have written: the longest part of the job is defrosting the ice from the coil. One thing I did that I didn't see suggested: plug the drain hole below the coil. I put a couple towels in the bottom of the freezer and ran the hair dryer. Didn't take long. I read that the amount of water created will overflow the pan under the refrigerator, so I plugged the drain hole. Once you clean that mess up, the repair is pretty straight forward. Great site. Even through I had to make two separate purchases, I still saved a lot of money. Thanks!

I have a GE Profile French door refrig. It's only about 4 yrs old and the defroster stopped working. I read the other repair stories and was able to narrow it down to either the temp sensor, defrost timer, or main board. The refrig section was up to about 47 degrees and freezer was around 25. I could tell it was trying to cool but couldn't. So I tried the temp sensor first. I cut and spliced the new sensor on the outlet of the Evap. Coil and it took about 15 mins. Turned refrig back on and waited. The coil started to ice over after about 5 hrs I left the back panel off so I could see if and when then heater kicked on. After about 8 hrs I looked in and saw a faint glow and water trickling down and running out the drain. Turned out the sensor was bad and wasn't telling the main board it needed to defrost. I would try the sensor if you are having the same issues before spending a lot of money on the main board, defrost heater and or timer.

it was easy the only thing was i had to cut old harness to remove 2 wires that went to coil that had to go back in the new harness other then that a peice of cake.

Little difficult getting the switch out, had to pry wth some force. New installation was real easy.

My refrigerator was making a high pitched kind of howling noise. The PartSelect symptom that was closest was “unusual noise” and when I clicked that it said the evaporator fan motor fixes the symptom 32% of the time. Since my freezer fan speed sounded like it was constantly changing I went ahead and bought one which PartSelect delivered promptly. The installation video was great and although my freezer was not identical to the one in the video, the video was still very helpful. The only thing it didn’t say was how to tell if my freezer motor was the one with the thermistor although I suspect that they all are and that PartSelect is simply trying to save us money by showing us how to splice in a motor without a thermistor. Anyway, since I would have had to disassemble the freezer before buying the part to find out for sure, I just bought the one without the thermistor. This just meant I had to splice the new motor in, just like in the video. I think I would have preferred buying the motor with the thermistor even though it was more expensive. In the end my problem is solved so I’m happy. This is the third time that I’ve had to repair this GE refrigerator and PartSelect has been a valuable resource each time.

i followed a video that was on your site, the video couldn't have been easier to follow it was step by step and very easy to follow, i replaced the evaporator fan motor and everything is working fine, i did notice that the evaporator coil was frozen pretty bad when i removed the back freezer panel i am going to check it again in a couple of weeks to make sure i don't have a defrosting problem as of now everything is fine i am hoping it was just the bad fan motor causing the coil to freeze up because of no air movement over the coil

followed you online video and it was easy and simple repair only took about an hour frig is back quiet and working fine thanks also parts come fast