All Installation Instructions for General Electric Dishwasher GSD6000G02BB

Due the the age of this dishwasher (13 years) both upper and lower racks were showing significant rusting.

This lower rack (GE part #WD28X25960) was ready to roll right into the dishwasher straight out of the box, no tools needed.

Parts Used:

Complete Lower Service Rack Assembly

Bob from Chandler, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Roller Broken on dishwasher

Popped out Old Roller, put in new one, pushing it together with a pair of pliers.

My only regret is that i didn't check the other side of the dishwasher... the other roller was broken also, and now i have to pay 5.95 shipping & handling for a .29 cent item

Check all your rollers before you buy just one!!!!!

Parts Used:

Dishwasher Dishrack Rollers and Axles

Sean from Cicero, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Leaking at the valve

Just like the video and replaced it

Parts Used:

Water Inlet Valve

Brian from DERRY, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Wrench (Adjustable), Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Bottom door seal leaking

Do not overlook the two screws on the bottom of the outer door panel.

Parts Used:

Short Bottom Door Seal

ROY G from GAINESVILLE, VA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Mainly leaking Rince Aid, but occasionally the soap door did not open to dispense soap

Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry then started filling with dishes and ran the wash cycle the next day when full. All is well.

Parts Used:

Detergent Dispenser with Rinse Cap

Edward from AVON, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Would only drain intermittenly

Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!

Parts Used:

Check Valve Flapper

C. from Lexington, KY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Old soap dispensor latch would not hold

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

Parts Used:

Detergent Dispenser with Rinse Cap

Kenneth from Dublin, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

The door on dishwasher soap dispenser broke.

Repaired the soap dispenser.

Parts Used:

Detergent Dispenser with Rinse Cap

Eric from SIMPSONVILLE, SC
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Heat shield on lower spray arm came loose and blocked spray arm from turning

Followed instructions on how-to video on website on how to remove and replace lower spray arm.

Parts Used:

Lower Spray Arm - Gray

Jack D from CLEBURNE, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Hinge arm link wore out

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

Parts Used:

Hinge Arm Link

Samuel from LAS VEGAS, NV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Our dishwasher lower arm had become clogged

HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!

Parts Used:

Lower Spray Arm - Gray