GSC3500N00BB General Electric Dishwasher - Instructions

pulled the racks out, replaced the broken parts....easy job

We considered buying a new lower rack for the dishwasher which we were told was a new dishwasher when we took over the house. The wheels were constantly falling off when sliding out the tray. They wobbled as well. With the weight of dishes in the rack and malfunctioning wheels, it was a disaster! We found your site on the internet and instead of a new rack we decided to order a whole new set of 8 wheels and axle roller studs. Installation was easy. It's like having a new dishwasher! Tray rolls in/out effortlessly. Great solution for the prices, fast delivery. Everybody is happy! Thanks.

Part was an exact match. Make sure to use plumber's tape on all threads. Had to really tighten fittings to prevent leaks. Screws are a little difficult to get to. Test for leaks first, before final installation.

I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.

I received panels about week after I ordered them, however the large panel came scratched. I immediately called your customer service who was extremely helpful and considerate. She ordered me a replacement and it arrived the very next day..

Excellent service, I was truly impressed.

Based on information gleaned from the internet, I suspected that the drain solenoid might have melted. I took apart the solenoid assembly and checked it out. I found that some of the plastic on the inside of the solenoid had indeed melted, making it impossible for the plunger that opens and closes the drain valve to move in and out smoothly and completely. I removed the old solenoid, replaced it with the new one, and the dishwasher worked perfectly.

Followed the instructions and it was easy. Made the washer seem brand new!...It is the best solutions for a small budget. We used CLR to wash out the washer workings and it really left a sparkle on the dishes... I am so glad you don't change the models so much that parts can't be exchanged when they wear...

After determining the drainage issue was caused by the solenoid, (by process of elimination; the hose was clear, drain opening clear, diverter moving freely, power to solenoid present during rinse cycle= bad solenoid. Solenoid showed signs of overheating upon internal inspection...) I transfered the bracket assembly to the new solenoid, re-attached bracket to diverter reservoir, connected spring and power and Did a test run. Solenoid works great! I did notice the shaft on which the diverter pivots leaking just a bit while moving the shaft. You might consider oredering a new gasket for it if you plan to replace the solenoid. Pretty easy repair. Especially considering the complexity of some other possible problems! Good luck!

I ordered a replacement from partselect.com and received it in just three days. The only difficult part was deciding how to remove the white plastic end caps on the sliding rails. Finally, I took a small screwdrive and pried out the crimps in the metal, pulled the old caps out, inserted the new ones, and squeezed the metal together again using needle-nosed pliers. Nothing to it!
Note: The configuration of the new rack isn't exactly like the original (size and placement of the prongs differ somewhat) but it fits perfectly and works great.

First we got all the water out of the bottom of the dishwasher. Removed the old, melted drain solenoid. Very important - DO NOT THROW ANYTHING AWAY. The solenoid that removed was melted; however I had to reuse the springs, brackets and plunger from the old solenoid. I had to scrape and clean (with a solvent) the metal plunger to reuse it. Once I got it cleaned up and re-used the old parts, mounting it was easy. However, getting that tiny lockwasher on the shaft was a real pain in the ass. Finally I got it together and it worked great.

There are 2 switches that should be pressed in when you move the handle to lock door, the switches usually go bad with time. Just take the six screws off on the inside of door, then remove screw on the underneath part of handle. The switches are located on the top part under a piece of 1 inch metal plate held in by a screw, remove that and you'll see the 2 switches, test the button on each one to see if it goes in and out, you'll hear the click to. Just unplug bottom first then the top if you need to replace the top one. Thats it.

Heard a noise in our dishwasher and ended up taking the entire pump and housing out and found a small sucker stick in the impeller along with a bunch of string and other material that needed to be cleaned out. Also found that the housing was leaking at the shaft that goes to the solenoid and dripping on the solenoid and had rusted the metal plunger that goes into the solenoid. Bought the housing and solenoid unit. 1 screw (bottom one) on the housing was rusted becaue of the water. Had to hacksaw the housing and then had to drill out that screw. Also, the pump housing screen is left hand thread and is tough to get out. Had to hacksaw that too. Be careful of the orientation of the metal ring in the impeller area. I did that backwards the first time and the motor would not move. Also, the electrical connector to the motor appears to be polarized so it can only go on 1 way-notice before you take it out. Be sure to screw the solenoid bracket back on tight and notice the spring orientation before you remove-the new one was different than the old. Bottom line is that it works fine, and for $40, it's fixed, rather than spending $800 for a new one.

Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.

Pulled unit out from counter (never had dishwasher issues before) to see if there was anything obvious with wiring or anything. Noticed that some little piece on the bottom looked to have melted (later discovered to be the drain solenoid). Removed the obviously defective part and looked it up on line. Found the name of it on Part Select's website then started shopping for best price. Came back to Part Select because the price was the cheapest I could find. Two - Three days later received part and put it back on and had the dishwasher back in place and in use within about 10-15 minutes. Marking my first ever dishwasher repair. :)

Just took the old rusty rack out and put the new one in its place.