GSC308PRS00 Whirlpool Microwave Oven Combo - Instructions

Well, the instructions on the computer site were very easy to understand, however, the difficulty lay in the fact that we were 2 78 yr old people and getting to the inside the oven, lifting up the element so that we could see where it should be connected and get it connected was a task. We had to get down on our knees and then get back up. That was a chore within itself. But, the instructions were easy and clear.
Bottom line if us old people can do it, anyone can.

Removed the door from the oven. Undid all the parts above the inner glass door. Installed the inner glass and reassembled the door. Reinstalled oven door.

I was able to remove the old element and planned it with what little time off that I could. This would have been maybe 20-30 minute repair at the most. HOWEVER! I was extremely irritated screws were not included? When I called to ask if they were missing they said they didn’t come with the element. Cost me a very annoying trip to the hardware store. Not sure if I missed it on the site that they don’t provide screws - would have been nice to know that before I started. Still scratching my head as to why screws wouldn’t be included? My old ones were as beat up as the element I replaced. I was so irritated I was looking for a spot to leave feedback. Product is fine. Shipping was fine. Sending these products out as they do? Zero stars on that.

EASY. FOLLOWED THE YOUTUBE INSTRUCTIONS ON THE WEBSITE.

Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!

1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1

Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.

First, I watched the YouTube video which showed how to replace the hinges. Then I ordered the hinges which came in two days. Using nothing more than the instructions I watched and a Phillips screwdriver, lI removed the door, set it on the counter on a towel, removed four screws, and then removed the old hinges. The new hinges fit perfectly and were held in place with two screws each. Then the door was reapplied to the oven. The oven door now operated as if it were new. I wish I had attempted the repair much sooner, as we could have avoided the difficulty with opening and closing the door.

I put the tray in the microwave???? Pretty easy.

You will need a screwdriver and two pieces of duct tape (very important) before you start.
Unscrew the plate that attaches and keeps the element in place to the oven wall. If the screws are rusty, replace those too at this time.
Very gently pull the element and the wires out into the oven cavity. Do not tug. Gently remove one wire from the burnt element and use a piece of tape to stick it to the oven wall. If you lose the wire or if it slips back into the hole in the wall, you are in trouble. Repeat with the other wire. Now assemble the new element in the reverse order, one connector at a time. Screw back the holding plate, and you are done. Takes less than 10 minutes to complete and your oven will be as good as new.

Ordered the part and was extremely pleased with how quickly it shipped and also the packaging was extremely secure. Will definitely purchase from this site again.

Cordless drill removed 2 screws replaced element and 2 screws
Done. Didn't use new bracket

I turn off the power in the breaker box and then unscrew the part and replace it with the new one

removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.

Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on