GSC278PJB1 Whirlpool Microwave Oven Combo - Instructions

re thermostat/fuse breakage after cleaning: I replaced the part a 2nd time within a year, both times after a cleaning cycle and after 10 years of no similar problem . This time, when putting the oven back, I cleaned all around the door frame and noticed the exhaust grill was heavily filled with dust strands. It's possible this reduced the exhaust enough to overheat the oven during long high temp cleaning and blow the thermo fuse. Just a thought.

replace thermal safety switch on back of oven

Turned the circuit breaker off, removed trim and the oven screws, pulled oven out, and placed on a stand in front. Electrical cord was just long enough without disconnecting. Removed the back panel, installed the old thermostat with the new one the same way. Used the same phillips screwdriver for the operation. Installed the oven using reverse order. Turn circuit breaker on, back in business. Prior comments definitely helped me a lot. Thanks.

This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long because the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!

Like others said, the trick was getting the oven door off. If you don't have the instructions, here's how: Open the door all the way. Shine a flashlight on the hinge, and you will see an open hole about 3/16" diameter below the hingepin and toward the oven. With the door open, put a 5/32" allen wrench or any other comparably-sized metal pin into the hole in each hinge. With the pins in place, close the door as far as it will go, which is almost but not quite fully closed. Put one hand under the door handle, the other hand under the bottom of the door, and pull the bottom of the door down and out. With maybe a little wiggling, it will come right out. That's really all there is to it! Taking out all the glass layers is straightforward; you don't need any instructions to see how to do it.

Had to screw off old terminal block & screw on new one

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

There are hinges on the door that need to be lifted up to take the entire oven door off the appliance. The screws are taken off of the door to get to the interior glass. The cracked oven door was simply taken off and replaced by the new one and the screws were put back and the door was placed by hooking it onto the appliance and the hinges were dropped down. Simple as that!

Removing the door was the first challenge but once the door was off it was a matter of disassembling the door to get access to the interior door. If you remove all pieces and line them up in the order that they are removed you have a good chance for success.

First, I'll say this website made it easy to find and order the part, it arrived quickly and reading others' reviews helped with installation. My Dad and I did the repair together, which really helped - my Dad is an fantastic handyman! We removed the door by lifting it up out of the hinges - a little difficult to get the right angle, but we succeeded with a little wiggling. We disassembled each later of glass/door, keeping each layer in order with screws so we could retrace our steps. I cleaned each layer thoroughly, which added to the time. Unfortunately, just as we were putting the last part on (exterior door with glass), the glass shattered as I tightened the screw! Ack! My Dad said it's because the glass was old and easy to shatter. Maybe I tightened the screw too much? So, back to the website I go to order the next part. We expect it to arrive soon. The bad news: another Christmas without an oven. The good news: my oven is now clean as new (I even removed the back fan cover to clean the fan - couldn't have done that without removing the door) and the parts added up to a fraction of the cost of a new oven.

Removed trim strip from each side of oven, removed one screw from each side hat held oven in place and slid oven out of wall. Finally found the thermostat located on the back side of the oven after removing the sheet metal on back. replaced the thermostat and reversed the procedure. Only difficult part was locating the thermostat. I thought it was on top, when in fact it was on the back. Pretty easy, really, and saved some cash in the process.

Turned off the power/ unscrewed the oven from the cabinet and slid it out took the back off the oven and the part was right there. What I would like to know is why this happens so frequently? This is the 2nd time and it always happens after the self cleaning is done.