GSC25C5EYB02 Whirlpool Refrigerator - Instructions

i didn't repair replace capacitor, bi metal defrost thermostat and still not freeze also replace light door switch any suggestion thanks

Just follow youtube examples. Work in freezer. Troubles was I didn't fix the problem. Experts say thermostat is the best one to replace (53%). Anyway they are not always right.

What took the most time was figuring out how to access the back of the pad. This is what I finally put together. First, remove the two screws(with nut driver) holding on the silver plastic cover around the water dispenser orifice and the ice dispenser chute. Next there are two or three black plastic clips that hold the electronic face in place. They are located near the front of the face on the bottom. Take a small flashlight and point it up from the bottom of the dispenser area, and look for a hole in the clear plastic with a small black catch in it. There is one on the right, one on the left, and I think one in the middle. I released these catches by pressing up in the holes with a small flathead screw driver while pulling out on the electronic face. One by one I got them free and the electronic face came away, revealing two Phillips head screws which held the dispensers trim in place. I removed the screws then pulled off the base or drip catcher part of the dispenser. It pulled straight off revealing two more Phillips head screws. After removing them I used my small flathead to work my way around the narrow trim piece disengaging the four clips on either side of the trim that locks it onto the backsplash liner piece. On the bottom I worked the trim up and down to get it to come free of the metal edges of the door and the plastic splash guard. It was kind of a hassle as its job is to lock the splash guard to the door, it hooks to both easily. Once the trim is off and the splash guard the pad is attached too is removed and in your hands its a simple matter to slide the pad up and free of the back splash. The red and blue wire has simple routing to the back of the electronic face previously removed. Disconnect the black connector at the end of the blue and red wires that lead to the pad you are removing. Install the new pad following the original routing path and reassemble dispenser face in reverse order of removal. Be patient and look around to locate the parts described, sorry I don't know their proper names so I am calling the parts names that make sense to me. I hope that helps. Best of luck.

I took off the broken tube and attempted to order a new one with the confusing we sight at parts.com- after 3 attempts I finally got the right part with help from the operator at parts . Com( nice and helpful) but had to ship wrong parts ( the 2 wrong ones) back. The parts were of good quality and we're not hard to put on

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by taking out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

Just plugged it in

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

Like you video

Popped out the old switch and replaced it with the one dying

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

Pull the broken one out, push new one in!

Took the old one out and put the new one in

just followed the instruction on utube