GSA20IBPDFWW General Electric Refrigerator - Instructions

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

Replaced top sensor in ref. and top sensor in freezer as well as defrost thermostat - works as advertised - easy fix, saved a bundle thanks to this site! Parts ordered and shipped quickly and without complications!

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

I followed instructions posted by experts and hands-on experienced owners on PARTS SELECT.Very helpful! Repairs was easy!.Defrost thermostat tried first,unsuccessfull then the DEFROST HEATER HARNESS next :BINGO !. Thank you PARTS SELECT ! Thank You every ones who posted their successful experiences that gave me confidence.From now on I know I can count on PARTS SELECT and its sites to solve my future headaches!

I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.

I took off the door and just swap gaskets. In my opinion do not need to take off the door from hinges .It very easy to take off old gasket and put in the place new one even door stays on a fridge..You can spend for this no more than 5 min.

Removed the panel on the back wall inside the freezer side. To do this I unplugged the appliance, removed the racks, drawer, bulb and two screws holding the panel in place. The defrost cycle was not working so ice buildup on the coil was to the point of blocking air flow to the refrigerator side. I used a hair dryer set on high and stuffed two towels at the base of the coil to collect the melting frost and ice. Once the coil was clear of frost and ice I took the defrost timer off by sliding the clip off the tube, cut the wires and stripped the ends so I could use wire nuts to make the new connections . Placed the new defrost timer in the clip and reattached in the same location the old one was removed from. The sensor was replaced by doing the same steps. I replaced the panel after all the wire nuts were secured and the wires were tucked away where they would not interfere with the fan. Replaced the bulb, drawer, racks and food and plugged The refrigerator back in. 20 minutes from beginning to end.

fallowed the short video and it was as easy as changing a light bulb

Used small screw driver to pry the top of the switch away from left inside wall of freezer side of side-by-side refrig./freezer; then used pliers to remove the switch; then removed the 3 prong socket and plugged it to new switch and installed it into the inside wall of the freezer.

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

My defrost was not working, so from time to time I had to remove the accumulated ice with a hair dryer. I did some research and found out it is typically caused by a failing defrost thermostat, or temperature sensor. I purchase and replaced both for 30 dollars. Really easy. I watched the instruction videos on the site at least 5 times, so when I did it, it was like I was doing for the 5th time. Now the fridge works just fine!!

I was intimidated by this repair(as I am with most repairs), because there were 2 possible problems. But being able to purchase both parts for $30 (including shipping) made it worth a try. Thanks to the instructional videos that were sent, the repair was much easier than I anticipated. For me, the hardest part was fitting my shoulders in the narrow freezer. Now the appliance works like a charm. This would have been a $150-$200 repair had I called a company to do it.