GSA20IBPCFBB General Electric Refrigerator - Instructions

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

Little difficult getting the switch out, had to pry wth some force. New installation was real easy.

Remove everything from the freezer. Suggest buying new rack holders when replacing the fan. I would suggest people who are not mechanical savvy to put drops of different colored nail polish on the screws and sensors so the know where to put them back. The job was quick and saved money from having to have someone else repair it.

I looked at the video that came with the part and followed what i saw. My wife and i was about to go out and spend between $1500 and $2500 on a new refrigerator due to continuous defrosting. It had been happening for about a year. I followed the instructions from the video and the defrosting has stopped. Thanks so much for the video and the part! We do not need a new refrigerator after all.

The mother board was bad....solder the board and it works like a charm.

watch you tube demo how to do it.

Followed the repair video, was spot on!!

I called a repair shop and they said the control bd. was bad. They replaced it and about 2 weeks later it happened again. They came out again and replaced the bd. under warranty. About a week later it happened again. This seemed like too much of a coincidence, so I looked around on the internet and found your site. The video showed how to replace the freezer safety thermostat which I ordered on Sunday and received on Tuesday. By then the coils were iced up again. I completed the repair in about half an hour. So far the old GE is working like new. Thanks for the help. I just wish I hadn't spent over $400 for incompetent repair people in the first place. Thanks again, you guys are great! By the way the part only cost about $17 including shipping.

luckly i have a bit of experience in refrigeration im an hvac technician by trade. this repair was a bit tricky in that i did not know at first if it was a Temperature Sensor issue or the main control board. I had tested the defrost termination thermostat and the defrost heater and as i suspected they were ok. Next i wanted to test the thermistors (temp sensors) it is hard to find technical data on these fridges. I needed to test the thermistors resistance @ a certian temperature to ensure they were working properly but where do u get such data? I also wanted to know some information about the logic programmed into the board (i.e when do you initiate defrost etc. . .). I had no such luck so i figured since i tested the defrost heater and thermostat and they were ok and all of the evap fans and such were working i'd order a circuit board and new thermistors. Got the CORRECT PARTS from this site in 2 business days and my fridge is working great! changing the parts was really easy, figuring out which parts to change was the only difficult thing about this job.

I went on Parts Select and typed in the problem, and they gave me the parts that might be the problem. So, I ordered the two parts, and put them in. Was really easy, as there are videos on parts select to help you remove the part and put the new one in. So simple. My freezer is working right now, so time will tell.

Open up the freezer make shore the fan is running/unplug the unit take out the Shelf,s take a 1/4 inch nut driver and take the back panel out pull out the ice box pull up on the back panel and pull it out to expose the coil it should be blocked with ice if it is take a blow dryer and defrost it unplug the fan and push it up. On top of the coil you will fiend the defrost timer take your hand and unstrap it and pull it out. Cut the wires and strip the wires back enough take the new part and wire nut the wires together and tape with electrical tape and put back on the coil. Put every thing back together your dun plug the unit in and wait over night if you can to let every thing cool.

removed the inside fridge electrical panel and swapped switches

easy pry out, disconnect wiring, connect on new switch and press in switch.

We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.

Part was received quickly and quickly installed-Thank you