GS2727EEDB Maytag Refrigerator - Instructions

Open refridgerator door, remove old filter by hand in a counterclockwise direction. Insert new filter turning clockwise. Close refridgerator door and fill a glass with water from dispenser. This will remove air and ensure water to free flow. Check for leaks.

First we ordered a new solenoid. . . The little piece that opens and closes whenever you push the button to dispense ice. That definitely needed to be replaced, and it was easy to do. However, that didn't fix the problem, so we looked and looked at the assembly and decided that a spring was missing. We ordered the spring, and when it arrived, we found that it matched exactly one that was already on the assembly. :-) Not the problem. Thirty minutes later we figured it out,. The diagrams at part select were not helpful with this. It was a matter of figuring out how the magnetic weight fit into the assembly. That's all it was! Now we have an extra spring for the future.

To replace the broken drive coupling on the motor end of the auger requires sliding the ice bin out of the freezer section of the refrigerator. Remove the ice cubes and let it thaw out for a few minutes. Remove five screws holding the front face on the ice bin to remove the ice auger. slip the new drive coupling over the end of the auger. reassemble and replace the face plate with the five screws. Slide the ice bin back in the freezer. Less than fifteen minutes it was finished.

Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mounting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.

Simply remove the ref door bracket at top and remove the door from the bottom hinge pin...Then replace the lower hinge, hinge pin and door closer... Reinstall the door and adjust for level...This took only 25 min to fix.

Called a serviceman. The Air return cover is NOT the cover we replaced. Ours is 3/4 of the way down on the freezer side of fridge. Put a thermometer inside, to monitor it.

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.

Repair very easy. Just followed the short video that you provided Took about 10 minutes.

We followed the directions in the video on the Parts Select website.My husband thought it was so easy and he isn't handy. I agree.

Problem caused by ice cubes falling out of ice bin and collecting at rear and interfering with ice dispenser drive. Broke plactic drive ring. Pull down 2 clips at front bottom of ice bin. Pull ice bin out. Dump ice cubes. Remove 8 star drive screws to allow case to move far enough to clear broken drive ring. Replace drive ring. Reinstall and tighten 8 screws. Install ice bin. Correct loose right side ice cube retainer board to prevent cubes from falling out of ice bin.

empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

Easy repair - Don't over complicate it. 1) Flip up ice bar to stop making new ice. 2) Pull out the complete ice bin/tray. 3) shut freezer door while you work on the ice bin. 4) All you need to do is remove the 4 screws holding the ice bin holding tray to the front of the Ice cutting section in the front. 5) Screw drive can then be pulled forward to remove the old/broken white drive cap. Just replace the White Drive ring, put the drive screw back into the ice bin tray and re-install the 4 screws. 6) When re-inserting the bin, you may have to twist the screw drive slightly to re-align with the motor bracket in the back of the freezer. Suggestion: throw out old ice because if it is wet or slightly melted, when you put it back in the freezer the ice will freeze/clump together into a large ice clump; not cubes. Also dry out the ice bin so there is no water to freeze up or create a new jam when the ice bin now re-freezes.

removed torx screws and replaced ice bin drive ring.

I watched the instructional video included with the shipping date e-mail(about 3 minutes long), and simply followed the instructions. It took about 2 days for the refrigirator section to return to normal cool temperature to the level set.

Replaced the plastic tray that holds the motor