GMC275PDB5 Whirlpool Microwave Oven Combo - Instructions

I am not a big do-it-yourselfer, so maybe I might have found this more difficult than expected. When I first looked at the oven before ordering the part, I saw a couple of screws and it seemed like an easy task. However, I found that I had to remove to whole door first, which was actually easy. Then I started to remove the case. Then I removed several layers of a puzzle. Oven door had 3 pieces of glass and 3 metal brackets. The installation video was for a completely different oven. Although I got out the broken glass easily, I had difficulty reassembling. The oven diagram for the parts was even deceiving. I had to involve my spouse and after an hour of cursing everything, we finally managed to get the thing back together. Whoever designed this oven must have been a deranged German scientist. However, everything is back to normal and I probably saved a couple hundred bucks for a repairman.

I did some research on blogs and identified the thermal fuse as likely culprit. Ordered part from PartSelect.com, but had to call the 800 number because the parts diagram doesn't show this fuse, just the thermostat. The fuse is located on the back of the oven, so it must be removed from the cabinet, but that wasn't a huge project. There are a bunch of sheet metal screws holding the top and back covers that must be removed. The fuse is held on by two screws and has two wire connections. Getting the stove out and disassembling is the hard part, but not really difficult if you take your time. I used a foot stool that was about the same height as the bottom of the oven and just slid the oven out on a piece of cardboard. Make sure you turn the power off before starting.

My mother and I were having considerable trouble baking or using the wall oven due to the escape of heat because the door wouldn't close properly. She, on many occasions, rested heavy baking pans/sheets on the door which, over years, caused it to "spring". Before I started the project I took a level and saw the door was facing down at least 3/8"-1/2" more than being level. I assumed it was the Door Hinges and after much research I found PartSelect who was extremely helpful in not only advising me as to the exact problem causing the door to not close properly but also in the ordering process itself. Because of the complexity of how the door is assembled I took digital video at various stages: removal of the door, disassembly of the entire door, removal of the control panel, and various small parts of the door - all with audio description by me as I went along. Because it took a few days to order and receive the parts I had time to clean the baked-on, caked-on grease inside all the parts to include the vents on the door and under the control panel using a power-washer when possible. I obtained auto-strength grease cutter/remover and soaked every "group" of screws in separate glass jars with covers (labeled). I also taped screws to a piece of paper, traced them to make sure they went back in the same place, and washed these as I went along. At the time the parts were received they were packaged in a fantastic way - quick shipping, easy to order, and I immediately started to reassemble the door. When I found my video wasn't enough to help me get the door assembled properly I used .pdf files I found on PartSelect which were extemely helpful and with a laptop close by I referred to the video I had taken and also SmartSelect's .pdf files. Because my digital camera was - and is now defective - I lost some of the most important video and this is the reason it took me almost 5-1/2 hours to reassemble the door. I wanted it to be correct given the oven is self-cleaning plus I do not want fires in the house!! All parts were laid out across three rooms and after being like this for almost a week it was great to have the entire oven back together again. At this point the oven door, when opened, is now facing "up" at least 3/4" as opposed to hanging down as it was before this project started. I closed the door and it actually pulled itself shut - something it hadn't done in years! The hinges came with pins already inserted so I didn't have to wrestle with the hinges to insert the original pins. The gasket was the easiest part to replace - simple removal of the old, worn, charred one and pop in the new one using the little clips that came on the hinge. The hinges themselves are extremely strong and well-made. After this project I have to say the oven now looks BETTER than when purchased, my mother has used it to cook with only once and it took 1/2 to 3/4 the time given the door is now completely closed because of the new hinges. I am totally satisfied with the parts, with PartSelect, will keep this site as a reference for further replacement parts if needed, and the oven is positively GORGEOUS after it was thoroughly cleansed of built-up grease. It looks BETTER than a new oven!! THANK YOU, PARTSELECT, for all your help and perfect parts!!

Removed trim strip from each side of oven, removed one screw from each side hat held oven in place and slid oven out of wall. Finally found the thermostat located on the back side of the oven after removing the sheet metal on back. replaced the thermostat and reversed the procedure. Only difficult part was locating the thermostat. I thought it was on top, when in fact it was on the back. Pretty easy, really, and saved some cash in the process.

There are hinges on the door that need to be lifted up to take the entire oven door off the appliance. The screws are taken off of the door to get to the interior glass. The cracked oven door was simply taken off and replaced by the new one and the screws were put back and the door was placed by hooking it onto the appliance and the hinges were dropped down. Simple as that!

Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long because the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!

Like others said, the trick was getting the oven door off. If you don't have the instructions, here's how: Open the door all the way. Shine a flashlight on the hinge, and you will see an open hole about 3/16" diameter below the hingepin and toward the oven. With the door open, put a 5/32" allen wrench or any other comparably-sized metal pin into the hole in each hinge. With the pins in place, close the door as far as it will go, which is almost but not quite fully closed. Put one hand under the door handle, the other hand under the bottom of the door, and pull the bottom of the door down and out. With maybe a little wiggling, it will come right out. That's really all there is to it! Taking out all the glass layers is straightforward; you don't need any instructions to see how to do it.

Removing the door was the first challenge but once the door was off it was a matter of disassembling the door to get access to the interior door. If you remove all pieces and line them up in the order that they are removed you have a good chance for success.

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

Turned off the power/ unscrewed the oven from the cabinet and slid it out took the back off the oven and the part was right there. What I would like to know is why this happens so frequently? This is the 2nd time and it always happens after the self cleaning is done.

Had to screw off old terminal block & screw on new one

I was able to convince a local mechanic that he could do this after watching it done four times. The most difficult part was unscrewing and taking out the oven to get to the back. He suggested since this has happened everytime I used the self-cleaning feature, that I cut a hole in the wall for easier access (tongue-in-cheek). The most difficult part was dealing with the extended warranty service plan - this is covered, but they could not find a technician to do this. Then I found out they don't pay mileage so who would want to come out to a rural ND ranch to repair an oven?

1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.

With some help from my wife.

When the oven is installed, there are two pins on the replacement hinges that are removed. If you were like me, you tossed these pins so you need to take a large nail and cut a 3/8" of material to replace these pins. This will allow the door to be removed when you open it half way. This is the most difficult part of the repair since you need to carefully pull the door off and a precise angle with an upward pull from the bottom. You will notice the new hinges have these pins so you can also try to get some new pins at a hardwire store that are similar. Next, you need to careful set the oven door down on a smooth work area and remove all of the philip head screws. The front of the door will be remove from the inside door piece by slipping it up a little when the screws are removed. The two screws that are on the inside panel hold the hinges. Take note of how you remove these since you will do just the reverse in putting in the new hinges. It would be a good idea to take the glass section off and clean it if you want to take on the extra challenge but you need to be very careful not to break these and that you put them back that same way it was removed. Now that you have it all put back together, you simply install the door back the way it was removed and then you can open it all of the way down to remove the pins in the hinges. Now would be a good time to put these pins in a save place with the rest of your paperwork for any further removal.