GLV1426P00SB General Electric Dishwasher - Instructions

The leak was coming from the drain valve shaft and I found the tips to replace the seal from this website. I was able to reach everything without removing the dishwasher from the cabinet. Once I got the cam lifter off the old push on nut was corroded so it was easy to get off. The old seal was recessed so I used the point of an ice pick to gently pry it out. The new seal was easy to push in place but the push on nut was a bear. I saw other comments about using a deep socket to push it on but I didn't have one the right size. I was able to hold the end of the shaft with pliers and pushed the nut in place using a screwdriver. Ran a short cycle and no more leak. Thank goodness for this website. Found the part easily and the other written comments were very helpful.

Just lift out the old dishrack and put in the new. Very easy and straightforward. Easy to order, unit came assembled. Happy customer.

Replaced with a new rinse aid fill cap.

Turn off water .Remove 4 screws holding lower front panels.Remove panels, valve is on left . Remove 2 screws that hold valve , slip valve up over clip. Using pliers slide clamp back, remove hose from valve.disconnect wire clip , unscrew from water fill line. Install new valve in the reverse order

replaced solenoid. worked properly after repair

First of all the part I ordered came a lot sooner than expected.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.

Replaced all ordered parts.

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

I removed drain hose to install 1 yr old dishwasher. Installed it fd water leak at drain hose. Removed it, found collection chamber was collapsed. This was a factory bo-bo. Collection chamber is made of p. V. C. I also had a problem with the sump filter ball. Called g. E. The told me to just put the ball in the chamber,not, the ball has to come in from the top, removing the spray arm,sump cover,major disassembly. Now I know how to completely dismantle a dishwasher. Home depot had no idea what I was talking about???now works great!!!!!!!!!!!!!!!

I couldn't do the repair because the parts arrived a week after I left, even though I paid extra for speedy delivery. And there was ZERO customer support - the phone message said they would not answer the phone, and the email response was a generic FAQ.

Received part, removed lower panel and shut water and power off to appliance. Used flash light to see under dishwasher, removed the two screws that held part in place. Loosed clamp that held the water tube in place to part. Placed towel down to catch water. Pulled the line out so I could get to the nut that is attached to inlet part. Unhooked the plug after all water was gotten up. The main knuckle that's attached to the pump was on so tight that I took it to my local gas station for an mechanic to unscrew it for me....I have arthritis in my hands. Station is only two mins from me and wasn't a problem for them to do for me. Came back put fresh Teflon tape on joint and reattached it to new part. Attached all hoses and clamps, plugged electrical prongs back in and attached bracket back to body of dishwasher. Turned water on and checked for leaks. Turned power back on and ran a cycle of dishes to wash....all went well. If the knuckle was on so tight the job would have only taken about 40 min at best.

There's a video on youtube from this site on how to install spray arm and base. Great video. Great price

Old baffles lift out and new ones installed - very easy

I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.

removed old drawer-like basket, installed the new duplicate replacement part. Easiest "repair" I've ever done!