GLGH1642FS5 Frigidaire Washer Dryer Combo - Instructions

watched video on replacing rear bearing.although rear bearing was not the part(s) i needed to replace, video instructed disassembly procedures to get to the drum glides. this was a very simple and easy to follow video. repair was a breezeand took roughly 25 minutes. the most time consuming segement of repair was vaccuuming out lint,that was 15 minutes. In future, as a preventative, i plan to remove front of machine to clean annually.
Thank you.

door not level son slammed shut and door strike broke

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

I followed the written instructions that came with the kit. They were relatively straight forward. Had problems getting the burner unit out.
Had to disconnect from 4" tube and disconnect all wiring.
Kit came with parts not needed.
Only needed to replace orfice and regulator control.
Tight area to work in.

Had to replace one Spring on top of the tub and both shock absorbers. Anyone with even a limited amount of mechanical ability could handle this repair. Save yourself about $300 in repair cost and replace these items yourself. Spring and Shocks absorber kit cost less than $60 with shipping.

Just look at the diagram that comes with the parts, it's a piece of cake. The most difficult part is replacing the spring, she is stiff. You will need to take the top of the machine off, which is super easy, and remove the metal keeper on top of the frame rail. Get someone to help you as you will need to lift the tub and slip the spring over the frame rail.

The shocks are the easiest part of the repair, and should take less than five mins. to replace.

Paid $27 total for a shock kit to replace the 2 broken stock shocks. Replaced them. It turns out it was not the problem, but just a symptom of the spider bracket (mates inner SS drum to drive shaft) corroding and breaking causing the drum assembly to shake out of balance. Found out is a systematic problem with this model washer, and no matter what else you fix, this will break and kill it at some point. Piece of crap!

Unplug, lift top, unplug 5 wires, remove 2 screws, pull dryer front away while supporting drum. Remove old glides, snap in new. Reverse disassembly procedure

disconnected electric and water supply. removed back cover from front loading washer. removed two screws from spring end plate on the top of the washer. replaced old spring with new spring/insulators by lifting the tub and hooking the new spring on. replaced the back cover and top spring cover plate. reconnected water supply and electric. machine is working like it did before the spring broke. very easy fix. the majority of the effort was moving the washer around to get easy access.

followed video and replaced part( cleaned and vacuumed dryer while I had it apart),relatively easy repair

spoke with repair person he indicated problem was not door switch but control board, prior to repair person arriving I receive the switch in the mail, I unplugged drier used a small edged screw driver to remove door light switch, removed three wire clips from the old switch, re connected the wires to new switch pushed the new switch into its location, closed the door light went out and the drier started and has ran just fine ever since, saved myself several hundred dollars or a new drier

E47 error code means control board or door lock. From reading other stories, I decided to try the door lock first since it is much cheaper. Frigidaire tech support was no help at all.

First I removed the "wire" and spring that hold in the rubber seal at the door.

Then I removed the 2 screws that hold the door lock in place.

Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.

Runs fine now.

Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

I removed the front access panel above the washer and removed the top dryer front panel. Then pulled out the drum and noticed the drum support ball stud had broken off, rather than order a new one, I welded it back on with a mig welder. I then replaced the drum support bearing and reinstalled the drum. I then installed the new belt before placing the front top panel in place. I removed the small vented panel on the back side to access the belt tensioner and fit the belt around the pulley and motor shaft. The whole job took less than an hour.

Removed old filter, installed new filter

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.