GLER642AS3 Frigidaire Dryer - Instructions

Replaced the heating element assembly. Problem was still there. Checked the electrical schematic to try to resolve. Everything checked out except the contacts on the motor M-1 to M-2 had no continuity. Removed the switch from the motor and exercised it. Works fine now.

Just snap into place

First, removed the metal access panel by removing screws. (EASY)
Second, pressed the timer knob onto the timer shaft. (EASY)
Third, mounted the start switch to the mounting surface. (A BIT DIFFICULT)

Fourth, pressed the start knob onto the freshly mounted start switch. (EASY)

Fifth, replaced the metal access panel by replacing screws. (EASY)

Dryer now functions like new.

After lifting the dryer top and finding the location of the thermal limiter on the back of the dryer, where it is difficult to get at, I carefully cut through the dryer cabinet with the multimaster on three sides to form a 'flap' upon which the limiter was mounted. By prying this flap open from the back, the two wires and two screws are easily accessible to replace the limiter, without having to remove the whole drum. Afterwards, I just bent the flap back into place and taped the seams. If it ever blows again, the fix will take all of about two minutes.

UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.

just pushed new knob on.

Just replaced the new lint filter with the old lint filter. The part fit perfectly. I did not have a problem.

The how to video was great. I had a little problem with getting the belt back on the pulleys. Not enough room for my hands. I did manage to get it back on ,and runs great

Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again

remove top of dryer by prying with large screwdriver to snap back clips that hold it on remove two screws on both sides that hold the door . remove door then remove belt from dryer tub. (to remove belt take the back panel near floor off with screwdriver and lift pullie up that hold belt. )then lift tub upward to disconnect it from it's seat; pull it straight forward to get to the heating element.un bolt it with screwdriver and disconnect the sensor and put new heat element in

Remove 2 screws from back of unit, remove top by lifting and pulling up, set aside. Using pliers,needle-nose, remove the 2 wires from switch, then using a magitized philips screw driver, remove 2 screws holding switch to back of unit, replace switch, reassemble everything. 20 minutes, boom, ur done, dry some clothes now

remove old knob and washer that was on it put new knob on and turn the knob dryer was save

watched you tube video... a breeze

Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!

Our heating element went out on our Frigidaire Affinity dryer. My husband is good at repairing things so we decided to order the part and do the repairs rather than hire a service technician. Before looking at the dryer we thought the back could be unscrewed and taken off to give access to the element but it did not. He had to take the dryer drum out to access the element. It was easy enough for him to do though and since we had everything opened up I was able to use the shop vac to get all lint cleaned out. I'm glad he did have to take the drum out after I realized the gasket on the exhaust pipe wasn't fitted on properly. There was some lint where there should not have been. Now that everything is clean and we have the new heating element installed we are good to go! The whole process of taking apart, installation and putting back together took about an hour and 15 minutes so not bad and we only had to pay for the part and shipping! Thanks PartSelect!