GLD7768V00SS General Electric Dishwasher - Instructions

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry then started filling with dishes and ran the wash cycle the next day when full. All is well.

Popped in the new one and done!!!

I took out the old rack and rolled in the new. I thought I was going to have to take the rollers off the old one and put them on the new, but they were already on the new rack. The hardest part was getting into the box. I am an 80 year old female.

I simply removed the bad part and reversed the process. It was very easy and a 12 year old could do it. Thanks for the online tips and recommendations. You saved me over 400.00 which is what a new unit would run. Plus installation. Many Thanks.

I removed the old rack and saved the flatware container. Then I put the new rack in.

The difference between the old one and the new one is that between a busted grocery cart with one wheel that always wants to return to the parking lot, and a well-trained dog that does exactly what I ask it to. The new rack was worth the $95 I spent to get it.

The new rack came with wheels and axles, so I didn't need to order more.

watched the video

Took screws out that hold front panel on, unplugged wiring, changed soap dispenser, and put everything back together. Not a bad repair at all.

Very easy - remove the screws around the inside of the door. 6 screws and 2 plugs to remove the assembly. Just be careful not the strip the sheetmetal screws when putting it back together. No screwguns...

Simple as 1,2,3.Parts on time and priced right.

It was an install. My problem is that the drain tube is not standard to other dishwashers,so I could not get it at either of the local home improvement centers. The good news is that it is larger than the standard, and offers better discharge.

I loved the service I received. The site pulled up the correct make and model basket I need for my dishwasher and gave me several options. I order with ease and it arrived within a couple of days. No tools required.

snapped on wheels

The repair was very simple. I removed all eight wheels and discarded the old axles by pinching them out of each wheel and replacing them with the new (and improved) axles. I then turned the rack upside down and simply snapped the wheels back on the spindles. It took me longer to explain this than it took to make the repairs.

The replacement studs that were suggested fixed the problem that we were having. The fix was easy and took less than ten minutes to take the broken studs out and snap the new ones into place. The studs are designed to hold onto the rack much tighter than the original studs and completely fixed the problem of the wheels falling off anytime you tried to move the bottom rack.