GI15PDXZS0 Whirlpool Ice Maker - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Light Switch Broke
Super simplet to fix. Popped out broken light switch and unplugged it and replaced with new switch. Received the part one day after ordering it from your company--AWESOME SERVICE AND TURNAROUND TIME!!! Saved at least $100 plus in repair costs/trip charge for something we were able to do. Great experience and would order from your company again. Thank you!
Parts Used:
-
Bonnie from Redwood City, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Wobble in fan made a ticking noise.
Pulled out the Fridge. Removed the plug. Removed the back panel screws with nut driver. Vacuumed the coils & fan area. Disconnected the fan cable. Used a socket and thumb ratchet to remove the 3 mounting screws from its sheet metal bracket. Slid the old fan assembly out. Assembled the new Fan blade onto the new motor shaft and attached the adapter cable to the fan connector. Slid the assembly into place and reattached with 3 screws using socket and thumb ratchet. Connected adapter cable to fridge harness and plugged in the power cord to test the fan. With it working Quietly and knowing the the problem was solved, the back panel was reattached.
Parts Used:
-
Andrew from Fairport, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!
While closing the door, I somehow cracked off the light switch button.
Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!
Parts Used:
-
Bruce from Duluth, GA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken spring in the light switch in refer
Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.
Parts Used:
-
Peter from Avila Beach, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken light switch
Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in
Parts Used:
-
Joseph from Francesville, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!