GFSS6PKBASS General Electric Refrigerator - Instructions

Unscrew old filter and remove(counterclockwise). Line up arrow on new filter with arrow on connection housing. Turn clockwise till resistance met. Do not overtighten. Follow directions. Simple.

First, I have to say I live in the next state over, and I recieved the parts the next day. Yeah! OK, I removed the adjacent drawers *and the removable lower storage shelves on the doors for clearance*. Taking out the broken lid is easy. The new one is a tight fit. The right side has a raised pad on the pivot point, but the left one does not. I worked the peg (pivot point) in on the right side and slowly and carefully pushed the stationary plastic left side in slightly(and sprung the lid slightly) to get enough clearance to get in the left peg without breaking the new lid pivot. While doing this, one has to make sure the shelf immediately behind the lid is in place since there are support tabs located on it, and you will have to rework the thing if you don't get them to mate on the installation.

unscrewed old filter by hand, installed new filter.

Removed the panel , snapped out the plastic window. snapped the window into the new panel , Install the new panel in the refrigerator

Until I figured out that the Metal cover on the divider door had to be removed (pried out) giving access to the hidden hinges. After that the hinges could be removed and replaced.Great with giving phone thou.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

opened refrigerator door located water filter location in right back corner unscrewd 1/2 turn and out it comes without shutting off water it is a snap to do by anyone and shipment was really quick thanks. People do not call a service tech for something this simple even a child tall enough can do it.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Leaking icemaker assembly was causing all of the ice cubes in the ice tray to freeze together. Remove ice tray, remove one Philips screw, pull the cover off, unplug the wires, remove the icemaker assembly by pushing tab and pulling the assembly at the same time. Replaced the water filter as well.

Repair was simple. I used a screw driver to help remover the clear window from my broken frame. The clear window just snaped right in to the new frame.

Nothing to tell it was just a replacement part that the old part was removed and the new one inserted. Works like a dream Thanks

If this repair looks hard then you probably aren't doing it right. The key to doing this fairly easy upper hinge replacement is to pry the metal back off of the swinging panel attached to the door as a first step. Doing so exposes the screws that hold the hinges in the panel, and also the tabs that you must press in to release and remove the hinge covers. I accidentally broke the tabs on both hinge covers removing them, but I discovered that it didn't matter - I was still able to snap them both into place without having to replace them as well. Once you've released the hinge covers slide the panel upwards to reveal the entirety of the hinge, then push the hinge up with a flathead screwdriver so that it slides off of the anchor piece on the door. Slide the replacement part down onto the anchor, slide the swinging panel down and replace the hinge covers. From inside the panel reattach the screws (middle hinge only) and replace the panel parts including the metal back. Whole repair takes about 15 minutes.

just had to unscrew old one put the new one in

Watched repair video from this site cleaned off shelf, removed the two bins, lifted it out broken shelf, placed new shelf back in, returned the two bins. One step that would have helped a little would have been to remove the bottom door pockets. This would allow the bins to come out easier.

pulled out the plastic cover which by the way is harder then reinstalling it, reinstalled it and had to put one side in and do a little bend in the middle to get the other tab in. just like new and took about 5 - 10 minutes.

thanks
><}}}}*>