All Installation Instructions for General Electric Refrigerator GFSS6KKYDSS

Door would not close properly

Spent a dollar 1.97 on the spring.7.00 on shipping and fixed it in less than 5 minutes.Fantastic

Parts Used:

Door Mullion Spring

Deryl from KINGWOOD, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Yearly replacement of filter

Moved stuff out of my way on the top shelf, reached in and turned old filter to remove. Filled new filter with water, lined up and turned to lock in place. Whew, never thought I would get that job done. :-)

Parts Used:

Refrigerator Ice and Water Filter

Robert from Myrtle Beach, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broken spring on french door

Placed lower spring leg in hole first. Manipulated upper spring leg into upper hole with needle nose pliers.

Parts Used:

Door Mullion Spring

John from CADILLAC, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broken mullion spring on left door

Placed one end of the new spring in left hole and used the needle nose pliers to insert the other end of the spring in the right hole.

Parts Used:

Door Mullion Spring

Dale from MACUNGIE, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Water flow 1 qt. Then slows

Water flow restrictions. Replaced flow valve. No help. Checked again and found filter head flow stopping valve broken. Replaced same. All good.

Parts Used:

Water Filter Head

Chris from OWASSO, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Bad tasting ice cubes

Took the old filter out and put the new one in.
Easy Breezy!!

Parts Used:

Refrigerator Ice and Water Filter

susan from hartford, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Warm refrigerator compartment.

Parts fit perfect. Very satisfied.

Parts Used:

Evaporator Fan Motor

Evaporator Motor

john from HAMPTON BAYS, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)

5 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Auto water stopped working, found that filter needed replacement

Unscrewed old cartridge, ordered new cartridge, installed new cartridge by following very simple instructions. Took only one day for part to arrive from PartSelect although I paid for cheapest shipping, which was "ground." I was amazed!

Parts Used:

Refrigerator Ice and Water Filter

Joanne from Fort Smith, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Water dispensed at a trickle

I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.

Parts Used:

Refrigerator Ice and Water Filter

JAMES from MORENO VALLEY, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

door spring

replacing broken french door spring.

Parts Used:

Door Mullion Spring

Libor from Danbury, CT
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Just follow instructions. Easy

Held spring with needle nose pliers and slipped into place

Parts Used:

Door Mullion Spring

David from NORTHWOOD, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

BROKEN VEGETABLE PAN RAIL

TOOLS NEEDED ARE A #2 PHILLIPS, A FLAT TIP SCREWDRIVER AND SOAP AND WATER FOR CLEANING OF THE VEGETABLE PAN COVER.

1. REMOVE BOTH VEGETABLE PANS.
2. REMOVE THE VEGETABLE PAN COVER BY SLIDING IT FORWARD ENOUGH TO BE ABLE TO LIFT IT UP AND OUT.
3. USING THE PHILLIPS SCREWDRIVER REMOVE THE 2 SCREWS HOLDING THE RAIL TO THE CASE.
4. IF THE REAR PART OF THE RAIL IS BROKED OFF AND STILL IN THE WALL OF THE FRIDGE (LIKE MINE WAS) REMOVE IT WITH THE FLAT TIP SCREWDRIVER BY PRYING IT OUT OF THE SQUARE HOLE . USE SOME PRESSURE IF NEEDED.
5. INSERT THE REAR PART OF THE RAIL (LOOKS LIKE A LANCE) AND PUSH IT IN ALL THE WAY TILL IT STOPS.
6. THE PHILLIPS SCREWDRIVER ANCHOR THE RAIL TO THE WALL OF THE FRIDGE FIRMLY, NOT TOO TIGHT.
7. USING THE SOAP AND WATER, CLEAN INSIDE OF THE FRIDGE AND ALL PARTS REMOVED.
8. LAY THE VEGETABLE PAN COVER ON TOP OF THE RAILS AND SLIDE IT BACK TO LOCK IN PLACE.
9. INSTALL THE VEGETABLE PANS.
10. WORKED FINE, LOOKS FINE AND LASTS A LONG TIME.

Parts Used:

Assembly RAIL VEG RIGHT

Steve from CARRIERE, MS
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Rail slide replacement

Watched a YouTube video and discovered there is a latch that needed to be depressed, then slide off the old assembly and slide on the new assembly until latched (you hear a snap type noise). Ta-Da! Task complete.

Parts Used:

Assembly RAIL SLIDE LOW R

LEANN from KEANSBURG, NJ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used: