GFDN110GD2WW General Electric Dryer - Instructions

Took off the top cover then took off the front panel and installed the new coils on gas valve.

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.

Followed the video which made it real easy.

1. turn off gas.2. disconnect electric.3.Remove 3/8 gas line from rear of burner. 4.disconnect two electric connectors from gas valve assembly. 5.disconnect electric line from igniter. 6.remove two mounting sheet metal screws from front of gas valve assembly(5/16 socket). There also may be a screw holding assembly to the bottom plate.7. remove entire assembly from dryer by pulling out to the front. 8.remove igniter assembly and replace on new burner. 9. two sheet metal screws 1/4 inch hold burner assembly to gas valve assembly.10.Install in reverse order . it may take a few seconds for the gas to get down to the burner. don't forget to change over the air mix valve to the same place.

My son ordered the part, but gave up installing it. We called in a professional appliance repairman because the dryer had to be partially dismantled to remove the drum and a belt so three sets of holes could be aligned to secure the replacement diffuser. My daughter had to lend a hand to hold one piece in place while the repairman threaded the screws because the drum was too deep for him to be able to reach both front and back pieces. Definitely not a one-person job for this particular model.

Followed the directions from the video about that particular part. I am 57 and it was fairly simple to do.

Followed the detailed instructions provided when I bought the parts at the online website. Very good directions diagrams/pictures and explanation of repair effort required

There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

I yanked on the piece of twisted felt and pulled it from between the drum and the frame. Model number and serial number were gotten from the placard inside the door frame. A schematic was found on line and the part ordered from that picture. The whole thing is held together by four Phillips head screws. Two are upside down in the top of the door frame on either side. A hand held impact driver with a #2 Phillips bit was necessary to dislodge those two screws. The remainder of the job was done with just a #2 Phillips screwdriver. After the two upside down screws are out the top just lifts off. It's held at the back only by location slots. The two remaining screws are under the top on the extreme left and right of the front and face downward. These hold the front door panel onto the frame. Be careful when removing the front panel with the door on it as there are wires near the bottom left corner that must not be ripped out of the door panel. What remained of the old gasket was removed from the grooves in the plastic inner panel upon which the front of the drum rides. The new gasket was put in place in that groove. Reassembly is just the reverse of disassembly. There's no reason to tighten down the two screws holding the top on with the impact driver when putting it back together.

very easy

Your site offered a video tutorial that removed any anxiety about doing the repair correctly. Removed front of dryer, disconnected wire assembly going to the front, replaced seal in seconds, returned dryer to original set up. simple. luckily. very easy to use website.

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.