GERC4120PB1 Whirlpool Range - Instructions

Element was sent by buyer, As they recommended, when model of stove given to them. It was upper right rear. When element came. First took off old element. ...Match both element , new element did not look exactly the same, small variation. It did not come on.. I moved old element from left side to right side . Old element worked on both side .. tried new element on left side also.. still didn't work.. so I called right away and explained.. new element did not work.. not defective, but, just wasn't the right one.. I had a specialist came and check it out also. I was told wrong element.

It was very easy just two screws. The easiest thing was ordering the part. Your company had a good schematic of my appliance so it made it very easy to get the correct part.
Thank you

took out the drawer by removing two fillips head screws, four more screws removed the drawer front. Two plastic push pins and the front panel was off. Put the new panel on secured it with the pins, attached it back on the drawer front, put in the screws and slid the drawer back in the stove, put the two screws back in, done deal!

after watching the video, installed the temp sensor. Super easy

Watch the video...

Well I had my oven door ducked taped together. I Am a 51 yr old female and I laid on the floor on my back to see if I could get the rest of the molding out without having to take off the entire oven door. I was able yo pop out the rest of the broken molding. I wasn't able to snap in the put it under the front of the oven door hold it together and screw in my new screw on the inside of the oven door. IT WORKED!! If I can do this so can you.

I had to unscrew the handle from the door as well as take out the front glass, put the trim in place (Thank God for the bottom placement nipples on each trimpiece), hold everything together after aligning all the pieces in place while I screwed the handle back on. The reason I was replacing the trim in the first place was that it is fragile plastic that had broken on both sides when I replaced one inner glass piece that had broken.

looked on internet on how to remove top. an easy fix after watching video

This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

My dual zone burner would trip my breaker anytime i tried to turn it on. All the other burners would work fine. I searched online and found a way to test my burner, which was shorted or grounded out. I purchased a new burner from the site...It was as cheap or cheaper than other sites. It showed up a few days quicker than i was expecting..I also replaced the switch to the burner, just as a precaution and to save time since i already had the top glass off of my burners....EASY JOB!

I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.

Removed the ifinite controlswitch and replaced it but i dont believe it is wired correctly. now it wont get hot until it is set on four or so. think i the way it is wired.

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy