GDWT608V00BB General Electric Dishwasher - Instructions

Simple as 1,2,3.Parts on time and priced right.

I removed six screws and unplugged the module and removed.
Replaced by the new module and plugged in and then replaced the six screws.
Very easy to fix.

I hand removed the snap in wheel axels and replaced the axles with new ones, by hand, no tools needed. On this dishwasher basket the wheeel axels just snap onto the metal cage "wires" of the roll out basket holding the dishes. Very simple. Used pliers to squeeze each old axle retaining nubs,from each of the eight wheels, , then just slipped (pulled the wheels off the axles) and discared only axles (that here the problem, detaching frequently from grasping the pull out dish basket, due to heat taking the temper out of their gripper (to basket).

First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!

It was very simple to install. At first my husband thought I had ordered the wrong part. I guess they just revamped the part and it worked out really well. And I didn't have it mailed special but I got the parts in about 2 days. My only problem is that the shipping cost as much as the parts.
But the parts are installed and the wheels don't fall off anymore!! If I need anything else I will use your company again and I will tell friends and family about you guys.
Thanks

The repair was so simple a child could do it. It took less than five minutes and now the drawer rolls smoothly and is quite sturdy.

Remove all wheels on one side. Use pliers to remove broken axles from wheels. Pop in new axles, then go to lower rack and attach to rack by pushing axle pinch mechanism onto rack support. New axles do not look like old ones—they are improved.

snapped on wheels

The repair was very simple. I removed all eight wheels and discarded the old axles by pinching them out of each wheel and replacing them with the new (and improved) axles. I then turned the rack upside down and simply snapped the wheels back on the spindles. It took me longer to explain this than it took to make the repairs.

I only had to repair the wheel axle. Since I read another post stating you don't have to change the wheels, I ordered only the axle and they popped right into the existing wheel and attached to bottom rack better than original design.

Very easy job. Just took out the bottom rack and replaced the wheels that kept falling off. A no brainer! works wonderful now. Most impressed with the ease of ordering and amazed how quickly the parts were delivered to me. I saved alot of money doing it myself! Thnak you

Used plier to pinch the axle head to take the old wheels off then pushed the new wheels on by hand.

The replacement studs that were suggested fixed the problem that we were having. The fix was easy and took less than ten minutes to take the broken studs out and snap the new ones into place. The studs are designed to hold onto the rack much tighter than the original studs and completely fixed the problem of the wheels falling off anytime you tried to move the bottom rack.

I inserted wheel axle into wheel and attached to bottom rack axle. It was simple. No problems.

Just pulled the old axles out and snapped the new ones in and slid them on. Wish all household repairs were this easy.