Models > GDWT358V50ES > Instructions

GDWT358V50ES General Electric Dishwasher - Instructions

All Instructions for the GDWT358V50ES
121 - 135 of 292
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
difficulty rolling the lower rack in and out of dishwasher
Replaced all 8 of the wheels and axles (the old axles wouldn't hold the wheels in place any longer). Replaced the tub gasket because of cuts from knives. Both fixes were relatively easy to do, although directions for the tub gasket would have been nice!
Parts Used:
Dishrack Rollers and Axles - Kit of 8 Dishrack Rollers and Axles - Kit of 8 Tub Gasket
  • Sharon from Northfield, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door had no resistance/no balance/would fall open
First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!
Parts Used:
Hinge Arm Link
  • Robert from Hampton, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel axle clips broken
Just pulled the old axles out and snapped the new ones in and slid them on. Wish all household repairs were this easy.
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Jerry from Spring, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The wheels kept falling off the bottom rack of the dishwasher
My husband took off all the wheels and changed the axles. We had friends who had the same problem and they led us to your web site.
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Suzanne from Oak Ridge, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed new wheels
I inserted wheel axle into wheel and attached to bottom rack axle. It was simple. No problems.
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Jason from Omaha, NE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
three lower tray wheels broken
Used plier to pinch the axle head to take the old wheels off then pushed the new wheels on by hand.
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Mark from West Point, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Axle attachment breaks on lower rack
Remove all wheels on one side. Use pliers to remove broken axles from wheels. Pop in new axles, then go to lower rack and attach to rack by pushing axle pinch mechanism onto rack support. New axles do not look like old ones—they are improved.
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Marc from Sebastopol, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
New wheels for lower rack on dishwasher.
Ordered on a Friday and parts arrived Sat. No tools required. Pieces easily slipped into place. Dishwasher is all fixed. This site is much easier to use than GE's. Will use PartSelect for all future replacement parts.
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Melissa from Vienna, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheels keep falling off dish rack.
So easy and the posts on the site were incredibly helpful in determing what part i needed. The wheels on the dish rack inside the dishwasher kept falling off. I had to keep lifting the dish rack in and out of the dish washer to load and unload it. Unbelievably annoying. I popped the old wheel axels out of the exisiting wheels and replaced them with the new wheel axels I ordered from PartSelect. Then I attached the wheels back on the dish rack and it was right back to normal.
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Jonathan from New York, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace original wheels on bottom rack
Very easy job. Just took out the bottom rack and replaced the wheels that kept falling off. A no brainer! works wonderful now. Most impressed with the ease of ordering and amazed how quickly the parts were delivered to me. I saved alot of money doing it myself! Thnak you
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Farrell from Grass Valley, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing wheel and damaged wheel
We had a missing wheel (probably melted in the dishwasher) and a broken wheel for about 6 months. Everyone in the house argued about who had to load/unload the dishwasher because the bottom rack would not move properly and was a hassle. I ordered 8 replacement wheels and axles and they arrived super fast. I was able to fix the problem in less than 10 minutes. I love my dishwasher again!! Yay!!
Parts Used:
Dishrack Rollers and Axles - Kit of 8 Dishrack Rollers and Axles - Kit of 8
  • Whitney from New Albany, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
none
installed the wheels
Parts Used:
Dishrack Rollers and Axles - Kit of 8 Dishrack Rollers and Axles - Kit of 8
  • Frank from Pittstown, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheels worn out
Rolled rack out-took a wheel off, put new one on without any tools. Then did the other five. This was easiest repair job in years
Parts Used:
Dishrack Rollers and Axles - Kit of 8 Dishrack Rollers and Axles - Kit of 8
  • Bill from Marietta, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rack does not roll correct, falls into tub
Removed old wheels and axles, installed new axles in wheels, clipped into place. I purchased new wheels and axles. Probably only needed the axles. The front wheels are narrower than the rear wheels. This probably contributes to them falling off the track. Since I purchased 8 new wheels (all wide, now I know what the second part number was for)I put all wide on. Seems to be more stable that way. New straight style axle clip appears more robust than the old side clip style. Thanks Parts select
Parts Used:
Dishrack Rollers and Axles - Kit of 8 Dishrack Rollers and Axles - Kit of 8
  • Damon from Austin, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
worn out wheels and axles
pop of the old, pop on the new! Wife happy, Priceless
Parts Used:
Dishrack Rollers and Axles - Kit of 8 Dishrack Rollers and Axles - Kit of 8
  • steven from westbrook, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GDWT358V50ES
121 - 135 of 292