GDS18LCPAWW General Electric Refrigerator - Instructions

I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel and it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

I watched the video and then read the instructions. Emptied and cleaned freezer compartment. Removed old unit and removed part of old unit to be used in new installation. I then installed the new unit and turned the water back on. I let the unit produce over night and through the first batch of ice away. Because of the various regrigerators this ice maker was used I had a little confusion recognizing our model, but worked through this problem useing some common sense. All around I'm very satisfied with the results.

Went well. Changed the Ice Maker and then the Water Valve. All good and it is making ice.

Barry G was right on with instructions and expectations of the process to trouble shoot parts and how to replace. Barry also provide the right part numbers for replacement items. Thanks again Barry.

Had to get behind the refrigerator and clean the drain out first and that took at least and hour. Just unplug the old motor. Took the old parts of the old motor, put them on the new one and plugged it back in.

took 1 screw out and removed ice maker and slid new one in and replace screw and connected power cord

After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...

Super easy, had my 15 year old do it (with my supervision).
Followed very clear Instructions that come with the replacement...
But, he could not get to the plug location until he removed 4 screws holding the motor assembly that spins the ice in the drawer and moved it out of the way...
Followed the rest of the instructions...
Works like a charm.

Took out one hex screw, disconnect electric couplings, pulled original ice maker out and found that the water supply line to the ice maker was frozen solid as well as the shute cup. Used hair dryer to thaw out the line and the cup reinstaled old ice maker and it worked fine. Did not have to use the new part at all at this time. Am keeping new part for future use.

Followed the video demo and would have been done sooner but for limited work space- narrow freezer compartment and the release tabs on the electrical plug. First home repair that the air was not blue and got done in under time allocated.

Went to GE website and researched the problem for the model, determined that it was 90% sure it was the Ice maker, I ordered it and it arrived the next day, installed it and it began working immediately,

Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!

Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.

Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.

The video on the GE site was great. Showed step by step instructions on how to remove the old ice maker and install the new one. Also helpful was the detail on the water chute which needed to be moved from the old ice make to the new one. Saved hundreds of dollars by not having to have a repairman do this work for me.