GD1329LED LG Dryer - Instructions

Part showed up in 2 days and repair took 2 min. Very easy. Thank you!!

There’s all sorts of videos on it I watched. It was actually very simple

Just unscrewed the original lock and screwed the new one on it was very easy

Removed the two screws holding the dryer door strike/locker assembly in place, removed the old and put the new in its place and replaced the screws.

Watched a repair video. Very easy to replace, about an hour to repair.

I watched a YouTube video with how to take the dryer apart and remove the sensors. I followed the what the instructions were removing the top of the dryer and then the front panel. Once that was removed it was a matter of removing 7 more screws and the lint collector piece came off. Popped the sensor pieces out. Cleaned the inside of the dryer and reinstalled a total of 5 parts and dryer is working fine and the clothes are drying in the allotted time it use to take.

FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.

To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any suggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson

I accessed the thermostats by removing the exhaust pipe and a plate where the exhaust can be ported on the side as an alternative. You need to get two hands inside to work. I struggled a bit before I noticed the removable access plate on theside. Took about 40 mins to get all three thermostats replaced. not too bad, but it is a tight working space.

It only took about 5 minutes to fix the problem. Took out two screws, removed old part, put the new one on and replaced the screws. Works great now!

Unscrewed the dryer latch on the dryer (not the piece on the dryer door) and screwed in the new piece! Bam, done and done. The ordering process was a snap, very friendly on the phone. She even emailed me a picture of the part before I ordered to make sure it was the right one, and was so patient with me, while my kids were sort of loud in the background. Thanks PartSelect.com, your part is quality and employee rocks.

Removed the exhaust duct screw and removed the duct. Hardest part of the repair was reaching in one-handed to remove the screws for the parts. Make sure that the screwdriver is magnetic. Changed parts and dryer working better than it has in months.

After replacing the wires and the heat thermostat I realze that I needed to replace the thermostat ntc and the thermostat to blower located under door was burnt during fire. I removed front panel,front facing and tumbler to reach thermostat inter wall. It was easy after fixing to other area prior. I thought it was very easy and didn't cosume much time. I'm a women and it was easy to fix.

removed the top of the dryer first by removing screws in the back and pulling the top back and up. Removed the control panel, followed by the door. The front panel and top brace were then removed. The belt was disengaged by pulling the tensioner idler and working the belt off the motor pulley. The drum was lifted out and set aside with the other parts. Holding the motor shaft with vice-grip pliers, and turning the nut on the blower wheel (left-hand thread!)removed the blower wheel. The motor is held by snap-on retainers and easily removed and swapped. Installation is reverse of disassembly. While in there, cleaned out the lint gathered everywhere. Also constructed a heat shield out of aluminum flashing and foil tape to cover the foil and foam tape between the burner assembly and sheet metal side. The foam had actually burned at some point in the past and the flashing should act as a better heat shield. A relatively easy repair, but should not have been necessary in a 7 year old dryer.

My lg electric dryer would not heat up. I went on line and found that the thermostats (there are two) could cause this problem. I used my dvm to ohm out the thermostats and found that the high heat thermostat was open. I replaced this thermostat and the dryer ran for a little while and then quit heating. When I checked the high heat thermostat again I found it to be open again. I then ordered and replaced both thermostats and the dryer has been working well since. The hardest part about this repair was the job of taking the dryer drum out to access the thermostats. I did however get good at doing this.