GCW1069LD LG Washer - Instructions

Took off the old hose with a screwdriver and put the new one on. As simple as that. You don’t need a repair man to get this done, you can do it yourself and save money too.

Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires

Change the thermistor

Viewed two (2) on-line video's for bearing replacement. Produced a 40 item "punch list" as to action to perform following video. Followed sequencing of video's. Noted a 10mm and 17 mm socket needed, used 3/8 drive sockets. Also noted that a "deep Socket" of unspecified size used to aid in removal of nylon pins attaching (3) shock absorbers. Found that 1/2 inch sized (SAE) socket in my 1/2 inch drive socket set fit in the confined space nicely. Did not need the "deep sockets" (3 plus inch overall length) rather a normal sized 1/2 drive socket worked nicely to depress the nylon pin retainers. During reassemble replaced outer tub gasket, checked bolt torque six (6) times over 45 min. to assure complete seating.

Followed the video instructions provided.

I followed the video on the PartSelect web site for this repair and it went just fine. I also replaced the drain hose while I had everything apart. Thank you PartSelect, same day shipping. Arrived within 3 day's and your video was spot on.

I BROUGHT UP THE YOUTUBE REPAIR VIDEO AND FOLLOWED IT STEP BY STEP AND WORKED OUT GREAT THANKS

Remove old one and replace. Just make sure it is all the way on and secure or you will have a huge mess on your hands.

Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.

Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

Basic skill

After checking for blockage on the drain hose and checking on any blockage on the bottom left corner filter and not finding anything i decided to open the machine. Everything suggested a broken drain pump
ITEM
PS3579318 Drain Pump and Motor Assembly which is located on the bottom left corner also and it attaches to the bottom left corner filter. And voila! The machine did not work! Now started throwing a FE code and it would not fill up. Well, the new pump was stuck! All i had to do was to stick my fingers in the bottom left corner filter orifice and move the fan like devices that make the new drain pump work, that did it! Be careful not to do it while the machine is pluged in, those plastic blades may hurt your fingers. To reach the drain pump you have to take the top, control board and front (door and gasket) of the machine off, about one hour labor.

unplug washer and disconnect inlet and outlet hoses. drain water from washer (about 2 gallons) by removing lint screen from front of washer. lay washer on side (I used a blanket to avoid damaging the paint) remove all the phillips head screws in the plastic bottom and the metal feet of the washer. Gently pull the bottom of the washer off. There are 3 shock absorber looking things that pull apart and are greasy. Try not to mess with them much. Just pull gently, and they slide apart. cut the zip ties holding the wires to the washer bottom piece. remove the screw in the lint screen area and gently pull the recessed plastic thing out the front of the washer. remove the screws holding the pump assembly on the front of the washer. Remove the three screws holding the pump assembly on the outlet pipe manifold. Installation is the reverse of removal, take care to put the shock absorber looking things back in gently and together at the same time when reinstalling the plastic bottom of the washer.