GCE23LBWAFWW General Electric Refrigerator - Instructions

It clips right in

Unplug the refrigerator. Gently pry old switch out with screw driver. Move wires to connector on new switch with needle nose pliers. Pop it back into the hole. Plug back in. Peek inside to see the lights working.

Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .

Replaced Temperature Sensor and now it is getting cold.

Uncovering the motor is the most difficult part. Installation is stupid-easy. Put all of the coverings back on in reverse order to the way they were removed. I don't think the ice maker has to come out but we weren't using it so it came out first.

This part worked marvelously. I followed a YouTube video to completion. Essentially, I removed the water filter cover by squeezing the tabs on the side. Then, I removed the housing for the light based on the tabs placement. I unscrewed the lighting fixture, unplugged and set aside. After that, I removed the bottom part of the damper assembly (that's not included but virtually attached to the damper) by pulling on its tabs' placements. Then, I pulled off the damper assembly, unplugged the cords and added the new assembly WITH the inclusion of the damper gasket assembly that doesn't seem to have been a part of the old assembly. Rescrewed and reattached everything and now the fridge is as good as new!!!

spent 10 minutes trying to clip in the seal without any success. I emptied the crisper drawer and removed it flipped it over clipped the seal. replaced the drawer. Secret is to remove the drawer from the refrigerator.

Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.

Taken longer to remove food out of refrigerator than replacing the part. Easy

Simply slide new control slide through slot from front.

i did not buy any part from you company. you do not state what it was i bought. i purchase a lot of items on line and they always tell me what the item is.

Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!

Found this site on the web. Told them my problem. They told me the most common part failure. I purched the part. Installed it per instructions. Waaa la now have a working refrigerator thank so much. U got the wife happy

I followed the video for my model refrigerator on parts select. My hint: when returning the back panel of the freezer, it's slightly adjustable left and right to avoid grazing the fan.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.