GCAP1800D1WW General Electric Washer - Instructions

The dial is held on the cycle control shaft w/a clip. Using a small pair of long nose pliers, pull the clip out of the slot in the control knob. Remove the outer knob exposing the indicator.Easy....

Reach down and grab the base of the agitator with both hands and yank up with slightly more pressure on the left or right, whichever side you prefer. This will break loose the holding clamps/pull straight up. To re-install: align slots and push down until it snaps. Simple as that.

This repair was a no brainer repair. The factory replacement knob that I bought from this site comes with a new "D"-Ring. Some other aftermarket parts houses sell the knob and the "D"-Ring as seperate parts. The knob from this site already has the "D"-Ring ring installed in the knob. My "D"-ring was broken and I simply removed it with my fingers. All I had to do was properly align the new know knob with the timer shaft and press it into place. If your "D"-ring is not broken and not still inside the old knob, you will need to pull it off the shaft with a pair of pliers before pressing the new knob onto the timer shaft. Dr. "B" The Hot Rod Doc

Watched the video. Followed the instructions. This has to be one of the best sites I have ever encountered. Even a caveman could fix the problem after watching the video.

I pushed a small screwdriver under the top lid and pulled the front out and lifted it out or the way. The rubber hose had two clamps holding it. One you loosen with a flat screwdriver and the other one you squeeze with pliers to remove hose.Then replace hose and put front back on. It's very simple.

Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!

reconnected the wires and turned the water source on

Removed clip from knob and pulled out old knob.Then got new knob and installed with the new clip ,very easy job.

I reviewed the service guide on Partselect and was able to take the old knob off the washer and say that the teeth on the knob had worn off, I called in and ordered the part on Saturday and the part was delivered in Wednesday, within 2 minuets from getting home from work the washer was fixed. My wife was ready to go out and buy a new washer when it only cost a little over $13.00 to get it fixed.

The hardest part is lifting the washer to get a the bottom. Disconnect the power, shut off water. Disconnect hoses and drain hose. Move washer from the wall about 2 feet. Tilt up front of washer. I used 4 12" long 8x8 inch lumber, lift washer….place one on each from corner. Lift again, place 1 more 4x4 on each existing 4x4. Now remove the belt off the 3 pulleys. Use the flat blade screw driver to remove the C clip holding the Pully on the shaft, with the flat bladed screw driver and hammer. Once the C clip is off remove the metal washer, pulley, plastic lock (apart of the bottom of the pulley & the thrush bearing and it's washer. Using the parts supplied (the "new thrush bearing is a bearing and washer combined) replace as you removed it. Thrust bearing, pulley, washer and, c clip. I tapped mine on using the flat bladed screw drive……becareful not to break it (they did supply 2 for me in the repair packet) make sure he c clip is secured. Lower the washer after removing all the tools from under the washer, by reversing the lift sequence. Slide the washer in place. Connect the hoses back up. Plug it in.Reconnect the drain hose, you should be good to go.

Pull hose out from wall and drain water into bucket. Remove two screws from back of washer holding on the clip. Pull hose out from washer its in there about 3 inches or so . If you order a new clip will make this even easier it's only $3.87 and I didn't realize I needed it. So, I just cut the old hose with a small saw near the clip so I could remove it and reuse it. Just slide the clip onto the end of the new hose - it fits into one of the grooves-I just made a note of where that was before removing from old hose. Then replace the two screws on the clip going to the back of washer. Put other end of hose into pipe in wall.

Followed the instructions on repair clinic video

Repair video is spot on but does not emphasize securing the drain pump to the washer before reattaching hoses. This holds the pump in place allowing you to compress the hose clamp while pushing on the hoses.

I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.

The replacement of this tripe water valve was so easy. My tub kept filling with water even though the water should have shut of. First remove the two hoses from the valve. Second you remove the 3 screws from the steel shield behind the plastic upper control pan panel. Take the shield off. Remove the control panel and lay on the washer. Then take the filler hose to the tub off using pliers to remove the hose clamp. Then take the two screws out of the valve. Twist and remove the valve. That is the removal. Reverse all of these to put it back on and test out. This valve fixed my problem. Anyone can do this who has any basic knowledge of tools.