All Installation Instructions for Refrigerator GB1924PEKB

lights wouldn't come on/work in refrigerator

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Parts Used:

Refrigerator Door Switch

Jane from Albuquerque, NM
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Broken clips on old part

Snapped in new part

Parts Used:

Damper Cover Insert

Rose from OCOEE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Old fill tube was blocked

Cut old fill tube into pieces, removed and replaced with new tube. Extremely easy.

Parts Used:

Refrigerator Ice Maker Fill Tube

David from VESTAL, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Original handle was loose.

Removed broken handle and replaced with new one by inserting 2 screws. Just took about 2 minutes and is a great improvement!

Parts Used:

Freezer Door Handle

Maryln from SANTA ROSA, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broken center crisper rail

Total time 10 minutes. 9 minutes to clear out the food and 1 minute to install the part. Installation was self evident and could have been done blindfolded. Part just snapped in.

Parts Used:

Refrigerator Center Crisper Drawer Slide Rail - White

Allan from Tucson, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broke the Rocker Switch in Fridge side

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Parts Used:

Door Switch

Sung-Su from BISMARCK, ND
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Bottom-freezer handle had a horizontal crack

Unscrewed the old handle, cleaned the area, and screwed on the new handle. Simple, and took just a couple of minutes. Our kind of repair!
The handle is now whiter than the rest of the fridge, but (1) were just happy to even find a replacement handle so we could switch it out and (2) no longer worried about it breaking and our having to purchase a new refrigerator just for that reason, when this one is still working just fine. Thank you, PartSelect! (We have referred friends to you :-)

Parts Used:

Freezer Door Handle

Diane from ARLINGTON, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Freezer iced up

Let the ice in the freezer melt while installing P trap drain tube

Parts Used:

P-Trap Drain Tube Kit

Dale from MECHANICSBURG, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Fridge was leaking water because of bad drain

Switched the drain out using the video tutorial
Fixed the problem
Have had no more drain issues

Parts Used:

P-Trap Drain Tube Kit

David from NEWTON, NJ
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

did not have a ice maker

remove parts that were not need installed water valve , ice maker unit and hooked up water supply tested and it works fine. got the parts really quick Thank You

Parts Used:

Add-On Icemaker Kit

Ralph from Argenta, IL
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set

5 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Water not draining to pan. It caused an ice build up under the freezer draw

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

Parts Used:

P-Trap Drain Tube Kit

Rich from WINSTED, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Glides were broken

Just swapped out new for old. Couldn’t be easier!

Parts Used:

Deli Drawer Glide- Left Side

Refrigerator Deli Drawer Glide

Jake from RICHMOND, VT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

One of the light bulbs went out on my Whirlpool refrigerator.

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

Parts Used:

SOCKET

Brian from LAKE CHARLES, LA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

I had a loose fitting old condensor fan blade on my new motor.

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

Parts Used: