FPFU19F8RFC Frigidaire Freezer - Instructions

I used the tool at Partselect that in theory allows diagnostic of the problem to be repaired. The result was that more tan 90% of the time with the introduced symptoms it had to be the thermostat. I order the part, got it quickly and installed. It did not fix the problem. So, be careful with the diagnostic tool, because it is just based on what most people buy when they have a particular problem. Videos for installation are great. If diagnosis was better, this would be fantastic. In my case there might be a different problem.

The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.



The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.

First of all thanks to all who posted their stories, because those stories helped me to narrow down what could have gone wrong with my fridge. I did not know how frost-free refrigerators worked at all, reading your stories and doing some on_line research I understood the theory behind the work. My freezer was working constantly, but fridge was warm, cold air would not reach to fridge because freezer was completely frosted.
I had ordered defrost heater, defrost timer and thermostat. I was sure one of these parts was the problem.
First I used flat screwdriver to turn the timer manually untill frdge stopped running(timer is on the left bottom corner behind the black decoratve plastic under the door) . Waited about 20-30 min, checked ,freezer was still frosted. I disconnected the fridge from the wall socket and took shelves out from freezer compartment. This is where hair-dryer came in handy or you could wait till ice would melt on its own, which could take long time.Then loosend 2 screws on left wall that were holding icemaker unit half-way , unplugged the icemaker and took it out. Then took the light-bulb and cover off. Next I unscrewed and took the posts out that were holding shelves in place. Then I took remaining screws from back wall out and gently pulled back cover up then forward a little until I could see electrical connectors behind the cover and unpluged them. Back wall cover was ready to come out. I discovered thick wall of ice covering entire cooling unit. Used handy hair dryer again. When the ice melted, I saw the thermostat was busted open ( Iguess water or moisture got into the unit, then froze and ice pop-openned the cover damaging one of the connecting wires). I diconnected wires and changed the thermostat , which was very easy, just one clip holding it in place . Then plugged the fridge and checked if heating unit was working by touching it. Negative. Closed the door and let fridge run for 15 min, turn timer with screwdriver until fridge stopped working, cheked heater again- wallah it was warm and then it got really HOT! and melted all of the new frost build-up(a sign that thermostat was working). Closed the door waited another 15-20 min, fridge came-on on its own. Unplugged the fridge, pulled it forward from the wall and used sponge to drain the water from holding tray- about one half gallon of it. This is a good time to use a vacuum clener to undust the back and under the fridge. Then put everything back, in reverse order, ofcourse. Cleaned fridge and freezer compartments with warm soap and winneger solution (really good- this was a present to my wife who took our two little daughters to grandmmas and out of my way), put everything back and turned the fridge on recommended settings. Its been 5 days allready and it works great ( I used thermometr to check temperature inside the fridge and freezer). I'm thinking of returning defrost heater and timer back.Thanks PartSelect.Com, I saved lots of money. Hope this story will be helpfull to someone.Thanks for your time!

Took about an hour previously to deice freezer, timer was running,drain was open, jumped defrost thermostat out and heater was O.K. Defrost thermostat was just a plug and play item, the time involved was in taking the freezer apart to get to it.

was very easy. just ordered a new ice maker which was delivered in a few days. The installation was so simple. Just plugged the new ice maker in and hung the unit on the 2 screws. And then tightened the screws with a 1/4 in nut driver.

We were looking for a new freezer --thinking it wouldn't be worth calling a repairman. I was trying to determine the size of the freezer and couldn't find it in the manual. So I googled the model number and stumbled upon this site. Thought it would be worth a try and $12 plus shipping to replace the thermostat. Got the thermostat a couple days later, followed the video directions to replace it--not hard! Plugged it in and it is working great!!! SOOOOO glad I stumbled on your site! You saved us $700-$800!! Thank you! Thank you! Thank you!

I had to tap the screw holes with a 8/32 tap so that the screws would not bind.

Parts Select is an excellent source for help and parts identification. I highly recomend them.
My first option was to replace the defrost timer.
After still getting ice and frost buildup in freezer I decided to replace the defrost thermostat.
Remove all shelves. Losen icemaker if applicable. Remove light cover and bulb. Remove all screws securing rear vertical cover. Carefully move back panel, disconnect icemaker and bulb assembly. carefully remove styrofoam cover at upper left and remove defrost thermostat. I tested the thermostat and found it was defective. It would not close circuit after being placed in a working freezer. Reverse procedure to replace thermostat.
This solved the problem

removed screws with from the back panel of the freezer; located defrost thermostat attached to coil with a metal clip; unplugged thermostat and replaced with the new one. Put every thing back together and it works perfectly.

After testing and eliminating the temperature control and the timer as the problem, I turned to the thermostat. I had to wait for the ice buildup to thaw and then could remove the rear freezer panel (this was the 3rd time: first, to discover the ice buildup causing the problem, second when it came back after a complete thaw and test the thermostat, and this time to put the Partselect thermostat back in). My thermostat was visibly damaged from water melting into ice and expanding the casing and eventually breaking one of the connections. I connected the thermostat connection wires (not recommended) to get by while ordering the part, which shipped faster than local repair places could get it from their warehouses, and at a fraction of the cost. I'm really impressed with partselect's fast service and all the knowledgable customers who have explained how they installed them. I now have an intimate knowledge of how my fridge works and saved hundreds in repair, or twice that in replacement. Thanks!

Removed water line. Removed two screws holding valve. Disconnected line from valve going to Ice maker. Replaced screws and water line. Most important thing in working with Parts Select was the information they provided when I called them. I had called electrolux and was given no information and was told they would send out a repairman at which point I told them to get lost. Cost of part $30.00 vs service call of $75.00.

just like the video show sa 1,2,3 yeaaa thanks

Old part threads : made in China (brass) New part : made in Mexico (steel). First, unplugged it from the wall. As for the valve, removed the two screws holding the valve in, disconnected the plug, took the pipe cutter, cut the blue line to the ice maker, cleaned up the cut, pushed that line into the new one and reassembled. Done!

TURN OFF WATER!! UNPLUG REFRIGERATOR!! Remove water fittings and electrical connector on old valve. Remove two mounting screws on pump bracket. Reverse procedure to install.

Installed new fill valve in less than 30 minutes and waited for 24-8 hours for results to no avail. Ice maker mechanism was shot and still would not work. Went to Lowes and bought entire ice maker add on kit for my model ice box and installed in 30 minutes and have been making ice ever since. Your 99% cure rate was 100% incorrect. Save the time and effort and go to a big box store and just get a new ice maker. By the way, it only costs about $20 more to do that.