FPCE22V3FA1 Frigidaire Refrigerator - Instructions

dismantled the top rear panel of the freezer and found I had the wrong part. Hand started the fan motor and it has been working fine since.

Emptied freezer, removed fan motor cover (2 screws), removed fan and motor (2 screws), removed old motor from bracket and reassembled with new motor, transferred fan blade from old motor to new), re-installed new fan/motor (2 screws) and reinstalled cover...

we removed the food from the freezer, disconnected the fridge , removed the cover, the evaporater fan was running, condeser fan was running, then we checked heater with multimeter and it was ok. next step we replaced the frostimer, and defrost thermostat . and then the refrigarater was working ok, problm was the frost thermastat damaged.

One of the three top comments from other replys had similar problems, so I took their advice, since the prices were resonable, I went and replaced two parts instead of just the defrost timer. If I had to do it a second time I could probably do it all in about 20 mins.

The temperature was slowing rising in the refrigerator section of a side-by-side. As a precaution, I changed out the defrost timer and defrost thermostat. The parts were not expensive. I then tested the defrost heating element with a multimeter and found the actual culprit was a burned out heater coil. I ordered the part one day and it was delivered by FEDEX the next day. The three parts were much cheaper than a new refrigerator and took little time to install, thanks to the Parts Select website and the how-to-install videos. Now the fridge works great and we saved having to buy a new appliance.

Part Select suggested probable causes and supplied videos of how to make the repair of a 25 yr.old refrigerator along with the specific parts to order. I was about to trash the old refrigerator but after replacing the parts for a total of about $40 and 1 hour of time it works fine now.

The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.

1. Unplug the refrigerator.2. Remove the storage rack and back panel in the freezer. 3. Locate the thermostat. 4. Defrost the freezer coils , i used a hair dryer. 5. Remove the thermostat from the cooling coil and then clip the connecting wires close to the unit. 6. Strip the ends of these wires and connect these wires to the wires of the replacement unit using the supplied wire connectors. 6. Heat seal with a lighter the connections using the water shield sleeves provided and further wrap connections with electrical tape. 7. Reconnect the thermostat to the cooling coil at the location it was removed from. 8. Replace the freezer back panel removed earlierand the storage rack if you have one. 9. Plug the freezer back in. My refrigerator has been working ever since the repair. There are several YouTube videos available that walk you through the diagnoses and repair process. They are very good.

Ordered new parts, removed old parts, put in new parts. Done.

Turned off Refrigerator by thermostat switch in Freezer Compartment,(allowing for light to work in freezer). Then removed all food from freezer side,then all shelves & basket drawer. Next, unplugged refrigerator from electrical source. Removed back of inside of the freezer. Located the Thermostat for defrosting cooling coil. Removed and replaced with new part.(Tip-unplugged the wires for the original thermostat, remove from freezer and cut off and splice with connectors provided with new part, it's easier because you're not trying to do this in the narrow space of the freezer). Then attach the thermostat with new bracket and plug thermostat wires back in, replace back panel, shelves, plug in power supply, turn thermostat switch in Freezer to normal setting. Wait for Freezer to cool and replace food. It's currently working like new. BTW I thought I need a defrost time as well...however after I ordered that part and received it, I turned the existing defroster timer manually with a straight ended screwdriver very slowly and it cycled and the defrost rods glowed/functioned just fine. Therefore I didn't replace defrost timer. I'll save the new timer for future repair if needed. All in all it was fairly easy, and I didn't have to buy another fridge. I was really pleased with the service of this website...and the parts arrived very quickly via Fedex. Thanks www.partselect.com ! KJ

I needed to determine if the heating coil was ok. I bypassed the thermostat, rotated the defrost timer manually with a flat screwdriver until it clicked. The coil heated up and turned a glowing red. So the coil was ok. After looking at the wiring diagram located on the back, the only parts in line was the timer and the thermostat. So I ordered both, replaced them, and everything is working fine. I went online about noon on Thursday, placed the order. The shipping indicated 2-3 business days. To my surprise, they were delivered to my home on Friday, mid morning. Great service from Part Select.

This is a top and bottom frige. I unplugged the fridge and I took off the sheld in the freezer and removed the blower fan cover and unplugged the fan to remove the back freezer panel. Be careful when moving the fan. It looks sensitive. I used a hair dryer to melt the frost to get to the screws. Because it was frosted the back panel was hard to take off. Don't force it too much, just keep melting the ice. Once it was off the radiator looking thing was completely frosted and iced over and I couldnt even see the thermostat. I started blowing it with the hair dryer and it started melting. It took an hour to get the ice melted enough to actually see and remove the thermostat. You may want to leave the fridge off for a day. I didnt have a choice because I didnt have anywhere else to place the food. I was using the freezer as the fridge. Thats how cool the freezer was. I cut the wires for the thermostat. Im sure you could check which is positive and which is negative. I just looked at the direction the wires went. This works but it is not guaranteed. Check for ground. Google it if you need to know how. I used the clamp connector things but I didnt have a clamper so I used a plier. It works but I didnt like how it clamped. The little tubing didnt work for me becuase I didnt have a solder gun to warm it up and using a match is not good. You'll burn the wire. Buy electric tape and wrap it around. Dont use regular tape. Go to home depot it costs 99 cents. Make sure all ice is melted. Go over everything with the hairdryer to melt the ice. You dont want it to start freezing and clog up the vents, expsecially the one that goes from the fan to the fridge. Before I put everything back together I changed the defrost timer because I figured its best to change it since you never know. I loosened the two screws but first I took offf the screw holding the timer panel. I changed the defrost timer and connected it back. Then I screwed everything together. Then I screwed in the back freezer panel but not the fan cover so I could see if the fan is working. I plugged in the fridge and the fan didnt work. If you look under the defrost timer panel, the timer has a round part that you can move with a flathead screwdriver. Move it lightly clockwise and the fan will start. I read that the fan goes for 8 hours and then it turns off for a half hour. Seems like a lot of time to be on but its been a week and the fridge and freezer are working real good. This website is good and the aprts are cheaper than Sears.

I original tried to repair the motor but was not able to. I remove the screws on the back plate and removed the the back plate. Removed the shroud for the motor and screws, unplug the power connection and removed the fan motor. Installed the new fan motor and reassembled everything. The refrigerator is working great.

with patience

Replaced the refrigerator thermostat. One hex-head screw in the rear and two tabs on the front hold the thermostat cover on. The temperature knob pulls off by friction, exposing two phillips-head screws that hold the thermostat in place. Two power wires and one ground wire are held on by clips. The replacement thermostat is a different shape than the original, but it is a direct fit. This replacement eliminated the problem. The only thing that made the job difficult was not having any instructions nor any wiring diagrams for the refrigerator.