Models > FH069FD4F > Instructions

FH069FD4F (ABWEELC) LG Washer - Instructions

All Instructions for the FH069FD4F
76 - 90 of 132
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
My Washer was leaking
The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you
Parts Used:
Tub-to-Pump Drain Hose
  • Bruce from West Hills, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
The bolt on the motor rotor loosened allowing the motor shaft to wallow out the plastic bushing in the rotor.
Unplugged the washer,removed the rear cover, removed the old rotor assembly & installed the new rotor with thread lock on the retaining bolt.
Parts Used:
ROTOR ASSEMBLY
  • william from Mobile, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Leaking water on my Hardwood floor
After finding you on google it was easy to repair. It saved me $95.00 service charge. Your direction made it very easy.
Parts Used:
Inlet Valve Assembly
  • William from Campbellsville, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Very visible tear in hose. It was 1 1/2" long
Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.
Parts Used:
Washer Hose Connector
  • Tresa from McHenry, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Magnetic door plunger broke
Super easy to find the part thanks to their diagrams. This fix was easy but I would definitely use this site again.
Parts Used:
Magnetic Door Plunger
  • JACK from Kingston, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
leaky inlet valve
found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support
Parts Used:
Water Inlet Valve - Hot Clamp
  • Michael from Granite Bay, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the water inlet was leaking
pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done
Parts Used:
Water Inlet Valve - Hot
  • gerald from wis dells, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
I had a slow leak coming from the factory cold inlet water valve assembly, and removed the top and found it rusted.
I removed the top off the washer, unplugged from the electrical, removed the three hoses and wiring plugs, removed the two screws holding the valve assembly in place, and replaced the part with the new. It was a very simple swap, and I even found a video on YouTube on how to replace it.
Parts Used:
Inlet Valve Assembly
  • Drew from Thomaston, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Water inlet valve coil was leaking water.
Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.
Parts Used:
Water Inlet Valve - Hot
  • Robert from Asheville, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Cold water inlet would not shut off
Extremely easy--remove two screws in the back of washer connect elec. connections one at a time connect cold water lines one at a time and replace the two screws ion the back and you are done. Took longer to pull washer out from wall and push back than it did to replace part. Saved me $75.
Parts Used:
Inlet Valve Assembly
  • ronald from Corpus Christi, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Water was not draining and was making a grinding noise
This was very easy to instal. The aplaiance repair co. wanted $240 my LG is six years old and would rather buy a new one if I had to spend that much, so I gave it a shot and it took me 20 min to install the part. Told my wife she owed me $ 180 for my labor.
Parts Used:
Washing Machine Drain Pump
  • Chris from Walla Walla, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Water was leaking from under the washer.
The bellows hose on the bottom of the tube had worn through where it flexed. This was an easy job except for the long reach you had to make under the washer to reach the hose clamps that held the part in place. These were spring loaded clamps which were easy to remove with pliers. I replaced them with ones that could be tightened with a socket wrench since it was hard to replace the sprung clamps.
Parts Used:
Tub-to-Pump Drain Hose
  • Richard from Blue Bell, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Water leaks at both valves
Disconnect electric and remove top cover and remove connectors and hoses then the valves
Parts Used:
Inlet Valve Assembly Water Inlet Valve - Hot
  • Tommy from San Marcos, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
My Washing Machine was not draining properly
The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.
Parts Used:
Washing Machine Drain Pump
  • matt from Fuquay Varina, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Inlet cold water valve leaking
Ordered a new water valve, easy installation, removed top cover of washer. Two screws and three hose clamps, done in 20 minutes.
Parts Used:
Inlet Valve Assembly
  • Howard from Aubrey, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FH069FD4F
76 - 90 of 132