FGP337GW1 Roper Range - Instructions

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

Unscrewed old pan and screwed on new one.

It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

I removed the handle from the door, replaced the old one with the new one............. 1, 2, 3, just that easy. The replacement part arrived very quickly and the price could not be beat. Would I use them again...........Yes!

I had to bring the new handle to the Hardware store and have them pick out screws that would work. The only problem is that I live 12 miles one way from the Hardware store. My advise is to order scews when ordering the handle.

Replaced trim kit found on site. Everything went well. No real problems. I will book mark your site for the any other parts I may need.

Removed the floor of the oven. Removed the flame difuser covering the burner. Igniter was in plain sight. Turned on the oven and saw that the element in the igniter did not glow. Removed the igniter. Found a replacement on this site. Ordered the replacement part, which I received 3 or 4 days later. Installed the new igniter. Turned on the oven. Saw the igniter element turn bright red. Replaced the difuser and the oven floor. Turned on the oven and bake 2 loaves of sour dough bread.

Took the old one out and replaced it with the new one, fits perfect.

Remember how you remove the glass. The side brackets go under the glass.

So, after several years of it bothering me, I decided to replace the oven panel. I ordered it one day and it arrived the very next day. It was an easy job to replace. Just remove two screws in back and replace the panel. While I was at it I also replaced the racks. Now I have a brand new oven,thanks to PartsSelect!

The first challenge is always how to get the appliance apart; in this case how to open the top of the stove. There are two clips one on each side towards the front that you need to push in to release the top. However before you do this you need to unscrew and remove each of the burners from the top of the stove. After that, push the clips in with a flat blade screwdriver from each side to lift up the top. You will need to remove completely the top back plate on the rear of the appliance to get to the igniter module where you plug in the wires from the individual igniters. Then you also need to remove the top four screws from the lower rear plate to allow it to be pulled open enough to help thread the wire from the new igniter through. After that you simply figure out which wire (they are individually colored based on their position on the burner) and disconnect from the igniter module. Carefully pull it out watching where it came from so you can rout the new wire in a similar manner. Then remove it completely pulling it through the top of the stove and replace with the new igniter. Reverse the steps to put everything back together and you should be good to go. Be prepared to take a little extra time to clean the cook top as once you remove the burner you will see everything that has over the years accumulated between the burner and the stove top. All together it took me about a 1/2 hour (including the cleaning).

Ordered parts that I thought were correct. BUT I ordered from the door parts... which gave me the wrong screw and unnecessary shims. What I really needed was the cabinet parts! At the time of doing the order, I could not find the owner manual... but found it before the parts arrived. That is what saved me and also thanks to me, for being a pack rat and my grandson finding the spacer on floor after it came out. That made it possible to fix the door. The screw I tried to install, but soon realized it was wrong. I went thru the pack rat stash and found the screw that fell out late last year.....! I then noticed the screw holding the hinge bracket was loose, now that is almost impossible to tighten because everything or tools that I owned were tooooo long (it's only 1 1/2" off the floor)! I tightened that and put the spacer and bottom hinge pin in. The screw was only 3/4" off the floor and difficult to get into the hole without a mirror on the floor under the spot. I finally used a clamp wrench to hold the screw and thread the screw into the hole. From there, most sockets are too long, so I did find a short socket. Now that still took me to the mirror, so I used the clamp wrench to hold the socket to tighten the screw. Thank goodness I am mechanically inclined and can look at a schematic to to understand how something works or I would have had to call for a mechanic. Also I should say ... FIND you manual before ordering to start with the right parts! Manual showed the parts of the cabinet and the door as one long picture, which helped with the repair and would have for ordering.

Pulled racks and covers out of oven. Moved stove away from wall. removed bolts holding igniter. Disconnected wiring harness. Reverse process to install new part.

The kit was not supposed to fit my particular model but I felt the picture was exact and took a chance and had it sent. It was a perfect fit and was easy to assemble and looks like a new stove. I paid one third of the cost estimates that I got from local appliance centers and even other on line sites. I'm very please with the product and the delivery was more than prompt!! I couldn't believe the service!!! Thanks!!

I used a screwdriver to take two screws out and then pulled up on the burner head. I then installed the new part. It works great.