All Installation Instructions for Frigidaire Dishwasher FGIP2468UF0A

needed wheels for the roller part of dishwasher

Just snapped the wheels on and attached the bracket to the existing part.

Parts Used:

Wheel & Bushing Assembly

Jeanette from Fort Lauderdale, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Upper spray arm separated from arm retaining nut.

VERY simple repair - just unscrew the retaining nut by hand and hand screw on the new spray arm and nut assembly. A 30 second fix!

Parts Used:

Upper Spray Arm

Michael from Cumming, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

upper spray arm kept blowing off

Easiest repair ever. The spray arm itself usually really is not the problem, it usually is the clip or gasket that holds the spray arm on. It wears out. This part is perfect for it supplies a new spray arm, nut and gasket/clip. I think it wears out due to a build up on the arm that puts too much pressure on the clip/gasket. Remember when taking the nut off, if you are standing above the unit with your arm inside, you turn the nut clockwise while looking down. Good luck.

Parts Used:

Upper Spray Arm

Perry from Waynesboro, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

upper spray arm kept falling off

This part fixed problem. The original part seemed to have a defect. Was simple to fix, simply took off old piece still connected and hand tighten the new piece on, it took about 30 seconds.

Parts Used:

Upper Spray Arm

Todd from Brandon, SD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

missing a wheel on dish rack

just slid the wheel on.

Parts Used:

Wheel & Bushing Assembly

Pam from Cherokee, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The part would constantly fall after every dishwasher run

Removed the old spray arm by unscrewing it from the top inside of the dishwasher. Then screwed on the new spray arm. Could not have been any easier and it has not fallen off since.

Parts Used:

Upper Spray Arm

Anthony from Massapequa Park, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

upper arm fell off frequently

Unscrewed the mounting nut and the assembly came off . A simple task of taking the new assembly and screwing it back on .

Parts Used:

Upper Spray Arm

Ben from Monroe, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Spray arm fell off during cycle

Unscrew old one and put new one in. Only issue we had was the new nut that screws the arm into place did not fit our machine. We had to take the old one off and use it instead.

Parts Used:

Upper Spray Arm

Dana from PATTON, MO
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Leaking tub seal

Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.

Parts Used:

Dishwasher Tub Gasket - Gray

Bob from Clinton, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Spray arm broke off

Very simple repair - in my case part of the upper spray arm broke off, leaving the threaded portion still in the dishwasher. Just unscrewed the remaining broken part, and screwed back in the new part.

Parts Used:

Upper Spray Arm

Adam from Euless, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Missing part

Just pushed it onto the rod that held the old one

Parts Used:

Wheel & Bushing Assembly

Michael from STEWARTSVILLE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Brass nuts holding heating element in place had split

All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.

Parts Used:

Heating Element Brass Nut

Jonathan from New Hope, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Wrench (Adjustable)

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Upper Spray arm fell off

The Upper Spray Arm is all one piece....so that was nice. You dont have to order all three pieces, like it shows in the diagram. Very easy to order and install parts.

Parts Used:

Upper Spray Arm