FFHT1621TW1 Frigidaire Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drawer support was broken
Repair was quite easy. Simply remove screw and replace part. My repairman charges a min. fee of $99 to come by. I did this myself and saved an easy $100! The part came very quickly--next day after I ordered it. Would definitely do this again.
Parts Used:
-
April-Lynn M from Berrien Centere, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The drawer support rail was broken
I unscrewed the old drawer support and screwed the new one in. It was very simple!
Parts Used:
-
Chevy from Jacksonville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drawer rail under top shelf broken
-
Sandra from Standish, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both support rails had broken
First, remove shelf unit from refrigerator and lay glass side down on a large flat surface. Observe, then pay attention to assembly. Spent more time with this, drinking coffee, and playing with puppy, than the actual repair. Only had to remove and replace two
phillips head screws. Replace deli - meat drawer after shelf unit is in place in refrigerator. Check for clearance for door to close.
phillips head screws. Replace deli - meat drawer after shelf unit is in place in refrigerator. Check for clearance for door to close.
Parts Used:
-
Alan from Blairsville, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left rail was broken
The shelf needed to be removed from refrigerator and then remove the screw and pull the rail from the bracket on the opposite end. After installing the new rail it turned out to be a fraction of an inch too long so I had to file the cracket on the shelf which is metal. The rail slipped back in and was perfect. Easy job.
Parts Used:
-
Marion from Center Point, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Parts Used:
-
Greg from henrico, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Socket set
1 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no heat when drying
-
Glen from North Tonawanda, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Broke The Draw Slide Stop Off The End Of Lft Hand Rail
Took all the item off the shelf turned it upside down on the table,worked rear off off the pin carefully,install new rail and refastened the front tab strip.
Parts Used:
-
lloyd from COCHECTON, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Original plastic hinge cracked across the middle
Removed 2 hex screws & old hinge, placed new hinge on cabinet & found that it didn't fit; one hole was about 1/8" off. Had to drill a new hole in cabinet top in order to attach new hinge. Hinge works fine now. I'm glad to find the hinge is metal; original one was plastic.
Parts Used:
-
Al from Sarver, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
right rail broken
-
THOMAS from WICHITA, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
shelf end gave-way.
-
Genevieve from Raymond, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Needed a replacement for a broken doo rack
-
Ron from Tiffin, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replacing a freezer door rack
It was a perfect fit and snapped into place in seconds. No instructions were required.
Parts Used:
-
James M from Charlotte, NC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Right Side Drawer Support Rail
First removed drawer, then shelf. Unscrewed the broken support rail. Attached the new one and screwed it on. Replaced the shelf, slide in the drawer, that's it. Less than 10 minutes.
Parts Used:
-
Richard from East Hanover, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Meat drawer, left slider arm broke
Took out the top shelf, unscrewed the slider, screwed in the new slider and that was it! Very easy and fast service.
Parts Used:
-
Lisa from Fort Atkinson, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!