Models > FFFW5100QA0 > Instructions

FFFW5100QA0 Frigidaire Washer - Instructions

All Instructions for the FFFW5100QA0
106 - 120 of 171
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
door strike broke
Removed two screws and replaced the door strike.
Parts Used:
Door Striker
  • Edwin from Cape Coral, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer didn't start
I took off the top of the washer. It seemed easier than playing with the door gasket. It took about 15 minutes. Everything worked great. The washer is working again. THANKS PARTSELECT
Parts Used:
Front Load Washer Door Lock and Switch Assembly Door Striker
  • James from Whittier, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The top striker tip broke off....
Remove the broken striker, screwed in the new one in less than 2 minutes...this is the second time it was replaced...the first time I was still under warranty...he took about the same amount of time to install ...I ordered 2, because I know it will be broken again....
Parts Used:
Door Striker
  • teresa from brooklyn, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer would not go in high spin
It is a front load washer with a dryer stacked on top of it.Insaw a video on u tube. I took a neddle nose pliers ang took a spring loaded metal ring off that is holding the grey rubber boot on . I peeled it back just enough to reach ih and get the door lock in hand.I then took a phillip screw driver and removed the two screws un the front off holding the door lock..I then reversed instructions,and put the new lock in.The complete job took lease than 5 minutes,and the part did the trick. My washer works as good as new.
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • Randall from Doe Run, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replaced Door Strike.
Two screws out, two screws in.
Parts Used:
Door Striker
  • Lee from Kansas City, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The door strike just broke (who makes a plastic door strike on a machine that gets used as much as a washer?)
This was easy as pie. I unscrewed the old & put on the new. That's it!
Parts Used:
Door Striker
  • Dulcenee from Bloomington, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
door strike broke while moving
very easy, just put in the 2 screws and it was fixed..
Parts Used:
Door Striker
  • Shari from Raleigh, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Error Code E43 - door lock problem - no spin
Removed retaining band around door boot and prized-off boot on left side to access door lock - simple screw driver replacement job. Deleted last error code. BUT - washer worked again for several days, and now code E43 is back and won't spin - problem is intermittent - so suspect it is NOT the door lock, but a wiring or control board problem. Ongoing.
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • Allan from Charlestown, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Door Striker
Removed two phillips screws. Removed old door striker. Replaced with new door striker. Replaced old phillips screws. Job takes less than 1 minute.
Parts Used:
Door Striker
  • Robert from Hyattsville, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken doorlatch
Remove the top cover and the doorlacth and unplug the old parts as simple as that
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • ricardo from nesa, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Latch was broken
Only two screws and it was done,easy repair
Parts Used:
Door Striker
  • Gene from Atlantic City, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't spin shut off with 6 mintes to go
I found this wonderful web site, after removing the cover and running a diagnostic to find it was either the door lock or the TCP control board. Control board unable to find any information on was scared to call the repair man as they usually cost about $500.00. I am a single mother and order the door lock and just like that I was able to repair it myself. Thanks you so much!!!
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • michelle from swanzey, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
washer would not go into full speed spinning
Turned off electricity. Unscrewed top panel. Took off top panel. opened door. Unscrewed door lock. Pulled lock up. Unplugged connections. Plugged in new part, positioned, and screwed in. Replaced top panel
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • Joe from San Diego, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
latch to door broke and would not stay shut
I unscrewed the two screws and replaced with new door striker and used the same two screws I took out. It took me seriously less than 2 minutes and I am a woman!
Parts Used:
Door Striker
  • Kamlyn from Huntington Becah, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door strike broke, (i guess it happened during recent move)
Super simple, unscrewed the existing screws, removed broken piece, attached piece, screw it in. Done deal!
Parts Used:
Door Striker
  • Melinda from Converse, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FFFW5100QA0
106 - 120 of 171