FFEF4015LWC Frigidaire Range - Instructions

Unplug the oven (very important). Unscrew the bad element and screw in the new one. Plug oven back in.

on the back side of the wall oven the sensor wire was ziptied tight. we had to totally pull oven out of its wall space, remove back panel, unhook zip tie, feed through sensor hole around insulation, connect and then replace back and return and relevel the oven. I have

After the smoke cleared and things cooled off, I switched off the circuit breaker for the stove and unplugged it. Then I used a Phillips head screwdriver to remove the to pack panel on the range. Then saw the circuit board that was damaged--all other wiring was in great shape and unaffected. Removed 5 stab connector wires from board after taking a photo of the colored wires and where each was connected (also marked on piece of paper color/position of each wire), and a plug in pin connector. Then unscrewed the electronic circuit board from the range front panel by removing 4 of the same type Phillips head screws that secured it. Luckily, found PartSelect website, who had the original OEM circuit board with the original white overlay that sticks to the front of the circuit board. Ordered the board after speaking to a customer service rep from PartSelect (who was very patient and helpful with me!), and it arrived in perfect shape and securely packaged in 5 days. Installed the replacement board, attached the wires to the plug in connectors and plugged in the pin connector to the pins on the board. Restored power by turning on circuit breaker and then plugging in the stove. It works perfectly!! Note: I also found a great video online which showed how to remove and replace the board. Also, I looked at circuit boards from other vendors on the internet, but they looked a little 'different' from the original one on the range, and I didn't mind paying a little bit more to get a genuine part that would function perfectly! Will purchase parts from PartSelect in the future. Very helpful customer service staff!

Turn off circuit breaker
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven

Just replace the parts. Too easy for an old man.

Removed the old & simply inserted the new one

It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.

Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!

Removed the old ones and inserted the new ones.

Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.

I unplugged the dead burner and plugged in the new burner. Very easy. No tools needed.

snap out the old one and snap in the new

Had to remove oven door due to cabinetry. Removed screws holding unit to back wall. Pulled unit forward to release unit from front roof and expose wire connections to unit. Trick #1--get both hands into oven to to remove wires from unit. Front hanger for unit was different than old unit. Had to remove front hanger from both units. Hanger from old unit had to be sqeezed onto new unit in the unit in the proper location to fit into the roof stirrup to hang the unit. Now, two arms and hands into the back of the oven to reconnect the wires to the element. Slide the old support into the stirrup and screw to back wall. Result, the back wall plate of the new element partially covered the edge of the light cover which will be a challenge to replace the bulb.

Remove the lower bake element by removing the 2 retaining screws that secure the element to the inside oven back. Carefully slide the element out. There are 2 wires attached to the terminals of the element. While removing be careful to not pull the insulation out with the wiring. Attach the wires to the terminals of the new element and reinstall in reverse order.

Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.

ordered an oven rack, stuck it in the oven --- how easy is that?