Models > FFBD2406NB9B > Instructions

FFBD2406NB9B Frigidaire Dishwasher - Instructions

All Instructions for the FFBD2406NB9B
106 - 120 of 437
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bottom door seal leaking on my dishwasher
Still have a slight leak, but I'm thinking it may just need time to seat itself.
Parts Used:
Dishwasher Door Bottom Seal
  • Alex from COMMERCE, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The DW had no lights and would not work.
While trouble shooting the issue, noticed that all switches worked and there was sufficient power going to control board but still nothing working. Ordered new control board and with only a Phillip's head screwdriver, I was able to remove cover and control board to replace. DW works like new after the repair.
Parts Used:
BOARD
  • Elizabeth from LONG BEACH, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Spring broke
Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.
Parts Used:
Door Spring
  • Robert from BAY SHORE, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dispenser failed to operate
Uncomplicated repair. Remove door, remove old dispenser, install new dispenser.
Parts Used:
DISPENSER
  • GENE from BRONX, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaked at the bottom of door.
My brother in law installed it for me. There was some difficulty finding the right angle but once we realized we needed to start at the very right side it went well. So far no more leaks.
Parts Used:
Dishwasher Door Bottom Seal
  • Lynda L from BRIGHTON, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water Leaking from Bottom of Door
Replacing the part was easy. Just pop the old one out and pop the new one in. This item fixed my leaking door problem. The old arm had fallen against the heating element, which burned a hole through the end. Water was shooting out that hole and leaking under the bottom door seal. Replacing the door seal did not help, but replacing the arm fixed the leak.
Parts Used:
Lower Spray Arm
  • Loren from Sacramento, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking Dishwasher
The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.
Parts Used:
GASKET
  • Andre from La Mirada, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dish washer leaking at the door
Pulled off the old gasket and replaced it the same way with the new one.
Parts Used:
GASKET
  • Brian from Milford, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher door strike piece broke. Door had to be propped closed each time dishwasher was used.
Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!
Parts Used:
Door Strike
  • Charles from Fort Washington, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower sprayer arm melted after being lodged
Pulled the old one off and pressed the new one on (plastic clips hold it on). Dishes much cleaner now.
Parts Used:
Lower Spray Arm
  • james from PENTWATER, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic piece that held the arm on was worn & dishwasher only 2 yrs old.
Arm screwed on and immediately fixed the problem.
Parts Used:
Upper Spray Arm
  • elner from new concord, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom seal on door came out and melted on heating element.
Took me about 2 minutes to repair, no tools to repair, very easy installation repair!
Parts Used:
Dishwasher Door Bottom Seal
  • Danny from Collierville, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door springs were broken and the dorr was very heavy to open and close.
I removed the two screws and then moved the dishwasher out a little bit (about 6 inches). I pushed the dishwasher toward one side to make room for me to change the spring with my hand and repeated the same procedure for the other side. After the spring change, I turned an old dishwasher to a new one.
Parts Used:
Door Spring
  • Yangde from Raritan, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plug for soap dispenser.
My future son in law did it. Looked at instructions on the app for the part. Didn't take very long.
Parts Used:
DISPENSER
  • Janice from ELK GROVE, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power. Power surge took out the whole board
Just so simple take out the Phillips screws take off the cover three screws hold on the board. Un plug the connectors place the new board in and replace the screws. Simple plug and play.
Parts Used:
BOARD
  • Terry from BELLEVILLE, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FFBD2406NB9B
106 - 120 of 437