This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
This white dryer lint filter screen collects lint as it passes through the dryer vent.
$36.24
In Stock
Questions And Answers for FEQ332ES0
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Drew
September 13, 2023
The dryer runs and controls operate, does not heat.
For model number FEQ332ES0
Hello Drew, thank you for reaching out to PartSelect. Based on our understanding of the issue, we would suggest you check the thermal fuse, part number PS419402. We hope this is helpful!
I need the elec block that the power cord screws onto, I've got a screw broken off
For model number FEQ332ES0
Hello Maurice, Thank you for your inquiry. We have researched the model number that you have provided and show the part you are looking for is the terminal block assembly PS419369, which connects the house electrical power to the dryer wiring harness. Good luck with your repair.
I am ordering a replacement timer knob for this unit today. I also need a replacement “turn to start” knob for this dryer. I looked on your site and referenced the drawings for “controls”. In that drawing it is identified as number 4. There are 3 the same size. The left one says “temp selections”, the middle says “end of cycle signal” and the right one is the one I need. Can you help me?
For model number FEQ332ES0
Hi Brian,
Thank you for your question. The knob on the right is the timer knob. The part number listed under your model number for the timer knob is PS418921. The other knobs are referred to as rotary knobs and they are used for the other functions on your washer. The part number listed under your model for the rotary knob is PS419266. We hope this helps. Thank you and have a great day.
This front loaded 220 Frigidaire under counter dryer heats but does not turn, spin or tumble. Can it be repaired easily with what parts?
For model number FEQ332ES0
Hi Judd, thank you for reaching out. Based on the description you have provided, it seems that there is an issue with the drive belt, part number PS1148434. You may need to replace it to resolve the problem. We hope that helps!
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum belt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
Unplugged Dryer. Opened top of Dryer, over the drum. Removed Thermal Limiter. Tested the Thermal Limiter - found it was open. Checked all vents and exhaust tube for lint build-up. Replaced Thermal Limiter. Closed top of dryer. Plugged Dryer back. Tested Dryer - it works.