All Installation Instructions for Roper Range FEP310KV2

burner plug broken

Cut wires removed old plug,new plug in wire nuts on.Put heat on shrink tube done.
Less than 30 min.

Parts Used:

Range Receptacle Kit

Norman from Newport, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

back burner would not heat

removed the heating element then removed the screw that holds the plug in on cut the two wires and reconnect the two wires and put back

Parts Used:

Range Receptacle Kit

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

wayne from whittemore, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Element had burned out, and the drawer glides were broken .

Replaced both .

Parts Used:

Oven Bake Element

Range Rear Drawer Glide

Allen from ASHLAND, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

element burned out shortly after purchase of range, one was purchased locally and did not fit properly, causing element to burn out

replaced element with new one , worked perfectly-

Parts Used:

Surface Burner Element - 8 Inch

Sue from INDIANOLA, MS
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

element not working properly

Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.

Parts Used:

Broil Element

PHILIP from NORTH PORT, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven would not heat up.

Unplugged the range. Opened the oven door and took out the shelves. Took the right screw out, but had trouble getting the left one out do to the age of the range. Unhooked the two wires and took the element out. Put the new one in and hooked up the two wires. Attached the two screws and checked to see that the element laid flat and then tighten screws. Closed the door and plugged the range back in and turned the oven on and it worked perfect.

Parts Used:

Oven Bake Element

Johnie from PARKERSBURG, WV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Stove burner burned out

Very helpful customer service Lady.
Helped me select the corect burner replacement.
And helped me get it ordered.
Repair went very well.
I recomend Parts Select if you need parts for.

Parts Used:

Surface Burner Element - 8 Inch

Ben from MONTICELLO, UT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

broken rear drawer glides

just replaced the broken glides with the new ones.

Parts Used:

Range Rear Drawer Glide

Jeff from Manhattan, KS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Removing an heating element that burnt into .

Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great

Parts Used:

Oven Bake Element

Jenny from GREENFIELD, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Old drip pans made to heating element un ever

Replaced drip pans and now everything is level.

Parts Used:

Drip Bowl - 8 Inch

William from DANBURY, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven heating coil snapped and would no longer heat.

It was so easy to change this out. Unplugged the stove and removed a couple of screws on mounting plate and pulled out the old heating element. Plugged in the new one and replaced the screws. Problem solved!

Parts Used:

Range Receptacle Kit

Diane from Gillett, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Rear drawer slide was broken.

Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.

Parts Used:

Range Rear Drawer Glide

David from Mauldin, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven Demon Possession

Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.

Parts Used:

Broil Element