All Installation Instructions for Frigidaire Range FEFBMZ96FCB

my burners would just heat up solid red even when i had controls turned down to 2 or 3. i would have to turn controls off and back on, then they still would just go back to glowing red

This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and Mama is happy!!

Parts Used:

Infinite Burner Switch - Large Element

Infinite Burner Switch - Small Element - 240V

Leota from AUXVASSE, MO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The surface element quit working, when I tried to remove it, the element cracked.

Turn power off to the stove! Opened the oven door, removed 3 screws holding the top down. Lift the top up. (Take a picture first of where exactly the wires go and where the prongs go) I unplugged the 4 wires from the element. Use a screwdriver and pry the prongs through the metal brace. Remove the prongs from the old element because they are a separate part and don't come with a new element. If you wish to continue to use the stove, tape the ends of the wires up, because they will be hot when you turn any other burner on.

Parts Used:

Radiant Surface Element

Lucas from HOPKINSVILLE, KY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Lens cover for the oven light

Very easy just had to pull the wire up that holds it secure.

Parts Used:

LENS

Larry from COZAD, NE
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

When I was cleaning the oven the plastic clock timer overlay melted.

I removed the back panel on the stove. Then I removed the switch plate, and pulled the melted plastic overlay off and replaced it with the new one.

Parts Used:

Clock Timer Overlay - Black

Nicholas from McHenry, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

N/A

I had open back cover and remove the switch than replace new switch. Makesure cable conection.

Parts Used:

Infinite Burner Switch - Large Element

Dineshbhai from Rincon HWY21, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Change on e of the inside glass

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

Parts Used:

GLASS

Ronald from Ozone Park, NY
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Crack in inner door glass

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.

Parts Used:

GLASS

Robert from Richmond, IN
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Burner switch work sometime.

I follow the video on your site

Parts Used:

Infinite Burner Switch - Small Element - 240V

junius from WICOMICO, VA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Burner not controlable

Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.

Parts Used:

Infinite Burner Switch - Large Element

Royce from KEENE, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Stove was dropped and had broken, bent frame and adjuster feet

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Parts Used:

Leveling Leg Assembly

Paul from PORT ORANGE, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The range element was not coming on

After settling that it was the Surface Element Switch, ordering and securing the switch, the first step was to disconnect the power to the Oven/Range. Next pull out the Range and remove the back and disconnect the switch from the top of the Range. Using the new switch I removed the wire connectors from the old switch and reconnected them to the new switch in the same spot that they came from. After connections were secure I reattached the switch to the back of the Range and reattached the back of the Range. When everything was back in place the power source was reconnected and that was it.

Parts Used:

Dual surface element switch

William from BENTON, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

burners 1 would not do anything burned out 2 when from normal to out of control heat would not keep a constance heat

turned off breaker 3 Phil screws open door and on inside range top I would reconmend a board to hold top up square tip for cross bar and pliers to pull wires off fit perfect works really nice

Parts Used:

Radiant Surface Element

Radiant Element with Limiter - 1200W

rick from Delta, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

EOC FAILED

I removed the panel on the back of the range, with a small socket head. Then I removed the old EOC. I took a photo of the wire layout to help, when I connected the new EOC, just a smart step. Connected the NEW EOC, replaced all screws and the panel.

Parts Used:

Electronic Control Board

obadiah j from SAINT CHARLES, MO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Old part was replaced by mfg’r. Wiring different. No drawings or any info was included to show wiring.

I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.

Parts Used:

Infinite Burner Switch - Small Element - 240V