FDBG2250SS0 Frigidaire Refrigerator - Instructions

Used socket set and screw drivers to attach ordered hinge, thankfully we had the screws just not the hinge. Wonderful to be able to find and order on line! Thanks so much!!!

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks

Push in on filter and it releases pull filter out. Slide new one in push in and it locks it. Run water for 2 minutes and it is finished

it is a very simple process. pull out the water filter. put in the new one after removing the plastic tops. slide the filter in place pushing to set it in place. run water through water spout on door of fridge for about 3 minutes or until all the air bubbles are out. and there you are ready for a drink of water.

problem still persists part did not fix problem. made repairs recommended per your site.

Once the filter arrived, I pushed it in that releases a latch and removed the clogged filter. I then pushed in the new filter and when it clicked, I ran a few cups of water through it to clear any debris left from manufacturing and the job was finished. Less than 15 minutes.

1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

Had a leak every night from refrigerator couldn't understand where from. Went on line and found some articles. I was referred to this sight by ads the articles and then in how to. I was pleased that a customer wrote their own instructions on what to do it was more concise clear and made preparation easier. First label towel cup and bucket needed too. Turn off water supply and electrical cord unplug then remove cover behind refrigerator vacuum and clean then. Water makes a mess so clean dry first. Then mark your hoses to remember order. Next remove old inlet and put in bucket it's pressure clamps so push in and it locks I chose to suction pipes and check for damage to pipes pin holes etc next I inserted into new inlet in order. At that time I turned water valve on checked for leaks at initial insert and new inlet. Next I plugged in unit cord. Waited. No leaks so far left for 30 minutes ran ice machine and water dispenser waited 20 minutes no leaks yet. Unplugged refrigerator unit. Installed the inlet completely to base and closed back paper panel after wiping water. Waited 24 hours then smiled no leak. Job done so far 2 weeks all clear. Hope this helps you will need screws driver and wrench for copper or main line I did find same part for less but this sight help me with good instructions the one they provide is for engineers architects lol not me I'm DYI

This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.

Pulled out the fridge from the wall, unplugged it, and turned off the water supply. Took off the cardboard backing at the bottom of the fridge. Cleaned the dust and gunk. Unscrewed the old valve. Unplugged the 3 electrical connections. Since the new fittings for the water lines were different, we unscrewed the old ones, lopped off the nipples, and inserted the ends of the water lines into the new connections (they were super easy - just push the line in until it clicks). Reattached the valve. Reattached the cardboard. Turned water back on, and plugged in the fridge. Our ice maker still didn't make cubes, though. So I took out the fill valve from the top rear of the fridge. It had a tiny piece of ice lodged in the bend of the back, right above where it connected to the water line. I rinsed it out, reinstalled, and now we have a full bucket of ice!!

watched the youtube video from PartsSelect and was able to remove old water inlet valve easily and install new one with little effort. The hoses on my refrigerator were a bit different than shown in video, but I was able to modify them and it's working just fine now. Thank you PartsSelect !

i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water

removed backing to refrig unscrewed 2 screws from bracket pulled unit out unhooked hoses and elec plug's / putting in new just reversed the instalation

My part had threaded fittings. The part that I received had snap fittings. Once I realized that that snap fittings worked with the bare tubing and not any special tip endings, I simply cut off the ends of my tubing that mated with the threaded fittings. I then had bare tubing that snapped into the snap fittings. Two minutes later, the part was in place and the job was done. Problem solved.