FDBB4365FS1 Frigidaire Dishwasher - Instructions

After moving the dishwasher out from the cabinetry, I removed the screws holding the pump in place. Pulling the pump from the formed plastic opening, I found a toothpick lodged in the pump housing. At the same time I noticed that the front o-ring was deformed due to being the incorrect size (too large). It was installed at the factory this way.

I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.

Repair was easily performed by removing old parts and snapping new ones into place.
I woulsugest that you take a picture before removing the old parts so that you can correctly orient the new ones.

Followed the YouTube instructions. Loosened 4 screws took off the front door panel and removed the old door and installed the new one. The video was very helpful!

Took the old out and placed the new in its place. That simple!

I think the videos on the site are awesome. Made both repairs after watching them. They explain the repairs in a simple to follow way.

Open door, Lift out old ,replace with new.

You tube video and it was so easy less than 20min had it fix

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.

The drain pump was making a high pitched buzzing noise which told us that its days were numbered. When I ordered the pump I found out that the dishwasher was really made by Electrolux for Whirlpool. Taking the pump off was a simple matter of removing two hose clamps and prying the pump off the frame. The hard part was realizing that it just pulled off without damaging anything. The new pump easily slipped right in and the screw in hose clamp was easily installed. However, the hose clamp that required pinching with the pliers was not that easy. I had to use a screwdriver to push it all the way on while holding the clamp open with the pliers. All in all pretty easy.

Followed the instructions given on the video, for replacing the drain pump. I did not pull the unit all the way out of the counter space just pulled it out about a foot. I had to lie on the floor to change the pump. That cost me some time for removal and installation, but I did not have to disconnect any water or electrical lines. I did unplug the power. The exchange went smoothly accept for the one spring clamp. Hard to squeeze and slip on. Would have been better to use a different kind of clamp. I have arthritis so that was an issue. All in all a good experience. A Big Thank You !! to this site . There instructions were perfect, the site is very user friendly. They saved me the cost of hiring a repair person. I'm a 75 yr. old disabled female, if I can do it then you surely can.

Completly disconnected and layed dishwasher on its side for better access. New valve support was 1 inch longer than original but created no problem. it took no more than 30 min. to complete job.

turned off electricity, pulled dishwasher out about a foot, turned off water too dishwasher, removed inlet valve and replaced it with new.

Finally we laid in the tub--be sure to support the lid. The grommet could be inserted halfway. Then trying to fold the grommet back we were able to use a screwdriver to force the rest in to place.

Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.