FAFS4073NW1 Frigidaire Washer - Instructions

Unscrewed two phillips head screws, removed damaged part, screwed on replacement part. Presto! Washer works again. I especially appreciated receiving the part less than 48 hours after I ordered it with only regular shipping charge.

removed top of washer then removed the screws that held the lock in place. only hard part was the lack of room to slide my hand down to get the lock from inside the washer,and put the new one in. managed to find a tech sheet in the washer to put the washer in a "service mode" that is where i could make the washer do a final spin.but it still gave me a code that the door lock was not working properly.(even though it still locked)replaced the lock with a new one and the code disappeared and did a full final spin.. thanks guys

Remove the broken striker, screwed in the new one in less than 2 minutes...this is the second time it was replaced...the first time I was still under warranty...he took about the same amount of time to install ...I ordered 2, because I know it will be broken again....

It is a front load washer with a dryer stacked on top of it.Insaw a video on u tube. I took a neddle nose pliers ang took a spring loaded metal ring off that is holding the grey rubber boot on . I peeled it back just enough to reach ih and get the door lock in hand.I then took a phillip screw driver and removed the two screws un the front off holding the door lock..I then reversed instructions,and put the new lock in.The complete job took lease than 5 minutes,and the part did the trick. My washer works as good as new.

first problem is the hinge get worn or broken from being leaned on. second problem is the door gets slammed trying to close it braking the striker. to fix the problem 2 screws for the striker, to permanently fix repair door hinge. and a big thank you for the people who own and or run this site. my order was lost and they got the part to me the next day.

I didn't have the right tool, so asked my handyman neighbor to come do a few projects and he had the driver in his pocket screw driver. it is a tip that is included in many multi-tip drivers. two screws removed the old and replaced the new. cheaper than local parts place, and no repair man. thanks

very easy, just put in the 2 screws and it was fixed..

Took off top. Removed 2 screws on Door Lock Assembly and replaced.

You must remove the top of the washer with screws on rear of washer. Top slides forward to remove. Once top is removed you can reach door lock mechanism from the top. Two screws must be removed from the front of the washer where lock enters mech. You can grab the mechanism from above by the wires that run to it. Undo wiring harness and insert new mehanism. Slide into place and attach in the front of washer with screws. This job is easy and can save you a lot on repair bills!

First we took the pump off and it was full so we hoped replacing it as the fan blades were broke and it didn't help. We replaced the control board and that didn't change it either. So I checked here and the door strike and door switch could be the problem so I ordered and put them on that was the problem. Thanks so much. Instructions were well printed and the job was about 5 minutes to replace. The washer works perfectly. We should have started with these parts first and it may not have cost so much.

1. Remove the spring clamp around the tub seal. 2. Pull back the tub seal in the area by the door lock switch. 3. Remove the switch assembly by removing two Phillips screws. 4. Remove connectors from switch. 5. Install connectors onto new switch. 6. Mount new switch on washer with two Phillips screws. Reinstall tub seal making sure to tuck it correctly on the washer frame. 7. Reinstall spring clamp.

Removed retaining band around door boot and prized-off boot on left side to access door lock - simple screw driver replacement job. Deleted last error code. BUT - washer worked again for several days, and now code E43 is back and won't spin - problem is intermittent - so suspect it is NOT the door lock, but a wiring or control board problem. Ongoing.

Take a deep breath and say, "I can do this. I will not pay well over $100 for someone else to come and do it."! Identifying part easy, mail very quick, web instructions clear, took out two screws, slipped out old part, put in new one, replace screws. I loved every minute of it and it cost $16.20 (part and shipping). Thanks, Part Select!

Removed two screws on the back of the washer top to release the top on the washer. Slid the top off and removed it. Opened washer door and removed two screws securing the door lock assembly to the washer frame. Reached in from the top of the washer to get the door lock assembly. Unplugged the old door lock assembly in three places and plugged the new assembly in in the same three places. Placed the new assembly in the same place as the old one and secured it to the washer frame with the same two screws located on the inside of the door. Replaced washer top and secured two screws at the top back edge of the washer... Tried the spin mode and everything worked great!!!

Removed two screws, installed new piece.