F1354FDS1 (ACREEUS) LG Washer - Instructions

took out the drain pump and replace with a new one

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

The problem ended up being the pump motor which discharges water from the washer. I figured out this was the problem after trying several things. I determined the motor was fine when it was empty. With the unit turned off, if you can rotate the tube with a quick spin and it lights up, probably this is OK. Then I tried to run it again and it went about 1/2 way through the cycle and stopped and started humming again. So I started emptying out the water, which I noticed was about 5 gallons which is way too much. so once empty, I took the pump off by turning unit on side. There are two hoses with hose clamps, and a few screws. Be careful to mark which wire plugs onto which side of the pump. One is brown and one is black. If you take the pump housing off, with the 3 screws, you should be able to pull the motor apart. Mine had water and scum from the wash in it, which was a dead give away that it was the problem.

Replaced rotor assembly by removing the back panel off the washer. Removed center bolt to be able to take out roto assembly. Magnets made it a little resistant, but with a little wiggling came off fairly easily.

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

I watched a YouTube video on the repair and I was fully prepared.the repair went easy

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

removed top, removed 2 screws, replace part. did not fix problem, the real problem was the water inlet valve, works great, easy fix. thanks

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy