EWA6500DCWW General Electric Washer - Instructions

Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.

1. take the machine apart, since the noise comes when the barrel is spining, I just watch for anything that contact to the axel.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.

The repair went just like the video! Easier than I would've hoped.

It tooke some time to figure out where the water was leaking. It was from a small hole at the lateral side of the upper third of the drain inlet tube. Removing the hose was easy. Attaching it to the tub with a hose clamp was easy, but attaching the lower end to the pump motor was quite difficult because the spring clamp that had come with the washer was difficult to manipulate. I had to replace it with a band hose clamp.

By the way, the hole in the hose had been caused by rubbing the hose against the drain pipe from the motor to the sink.

I removed the agitator by simply pulling up. I then removed one bolt to get the agitator coupler off. I installed the new coupler, replaced the bolt and slid the agitator back down.

replaced them & working fine now....

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

After doing some troubleshooting, I found that the Air Bell was stripped inside.

First I removed the agitator by firmly pulling it straight up. Then I removed the bolt holding the air bell (agitator coupling) with a ratchet. Then came the hard part. The air bell (agitator coupling) was stuck on the shaft and would not come off. I used rope to lasso under the coupling and tied it to a 2x4 for leverage and eventually wrestled it off by using an upward jolting motion time and time again. Spraying WD-40 in the coupling seemed to help loosen it up.

Prior to installation, I cleaned the grooves of the shaft by scraping them out with a flat tip screw driver. Installed the new coupling by tapping it down with a hammer until it was seated firmly and locked it down with the new bolt. Aligned the agitator and slid it down until it latched. Done!

Easy enough. I had some help tightening the hoses to the inlet valve. I watched the video about how to repair and it was straight forward and easy to follow. You'll need a bit of strength to tighten the hoses to the dual water inlet valve. Be precise when lining up the threads of the hose and the inlet valve...don't force it...find it...if it goes on crooked it will strip the threads and wreck it. Recommend purchasing some plumbers tape to wrap on the the threads of the Dual Water Inlet Valve. Fixed the dripping water problem immediately.

The repair would have gone well, however partselect sent me the wrong part. Instead of a washer belt, they sent me a door seal to what looks like a refrigerator

Watched the video, good video. But instead of taking the bolts out first, it's easier to remove bolts last, to give support to remove the hoses.

I had to take out the front panel to access the Tub. Afterward the work wasn't hard.

The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on diagrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.