ETS22XBMBRCC General Electric Refrigerator - Instructions

I ordered the part on Sunday and had it by Tuesday. It only took a few minutes to install. Basically, I unplugged the unit and removed the cover over the motherboard with a nutdriver. The wires were easy to unplug and reinstall. There was no way to incorrectly install since they could only fit in the correct position. I reinstalled the panel pluged it back in and now the fridge is working great.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.

10 minutes total.

Took the three screws out of the cover, took the six plugs off of the board and removed board.

As it turned out much of the electronics is driven by 13.5 volts off the Main Control Board. The Ice Dispenser caused the problem because it over currented the depleted board power. You could hear a clicking noise from the board which was the main relay short cycling and not staying energized. While waiting for the replacement board I unpluged the condenser fan which is a DC motor and uses the Board power. In place of that fan I use a small table top fan to keep the condenser cool. As it turned out I only needed it for 3 days because Parts Select did a super quick job of delivering the new board. Thanks for the super service!!!!!! Removal of the board only required unpluging the electrical connections squezing the retaining board pins with pliers and pulling the board out, pushing on the new board and connecting the electrical plugs. If the board locks like mine did, just unplug the main board power plug, let the memory clear and replug the power plug. The unit should then start and run with no problems.

I went in with the toolbox, and couldn't see the screws to loosen, so I tugged the gasket to see how it was attached. It just snapped down into a groove in the door. Pulled out the old one, snapped in the new one, and voila, it was done! Happy day, lucky me! Didn't even need my husband's help.

I noticed that if I unplugged the refrigerator and plugged it back in a while later it would start working but eventually would stop. I deduced the problem was likely the defrost thermostat. I ordered the thermostat but it was in a difficult place behind the evaporator coil which I could not remove. While I was trying to work it into position my hand pressed against the defrost coil and shattered the glass sheath. I ordered the coil and finally managed to get it and the thermostat installed. The refrigerator seems to work fine now.

I watched the on live video. Piece of cake!

Thanks to the very fine posts on this site, and availablity of parts, I didn't have to call in a repair man. Due to the near-10 year age of unit, I first ordered a new fridge for the kitchen and moved the GE to the garage. Let it manually defrost. Figured based upon comments posted here I was dealing with the defrost system problem so ordered the temperature sensors for top and botton, the defrost thermostat, and the defrost heater. As a wise poster said, if I am going to pull the damn thing apart, I'm going to make sure I have all three parts in case I need a particular one. Do not have the skill or gauges to troubleshoot electrical components. Parts arrived from Parts Select in great time, and excellent packaging protection. Parts Select also has great diagrams of the unit, although I could not find written repair instructions anywhere. At first I was going to wait for the parts to arrive and replace everything, but since there was a dely in getting the new fridge in, and the freezer section of the old fridge worked fine, once I had defrosted the old fridge, and cleaned up a few of the rusted over connections, I put everything back together, to await new fridge and receipt of parts for old fridge. Well, as is the story of my Karmic life, once fridge defrosted, and I put everything back together, plugged old unit in inside garage, everything came back up working perfectly on the recommended settings for both freezer and fridge sections. Has continued to maintain correct temps for over a week now. Also have new fridge. Don't recommend the top freezer Maytag one for about $700, as construction is cheap, and temps fluctuate all over the place. Had Home Depot exchange out for the LG $740 top freezer model, and am really impressed with its construction and performance so far. (Both units are recommended buys by ConsumerRepots.Org) Not sure how long old unit will keep running correctly, nor what caused it to come back to life after the defrost. Perhaps a simple clogged drain tube, or shorted out rusted electrical connections that I cleaned. Anyway, am keeping Part Select parts on hand for possible future breakdown, and enjoying having both fridges running. We needed additional freezer space, and got the peace of mind of a new unit for the kitchen.

First, we called Sears Repair and had a technician come to our home. He stated the motherboard had gone bad probably due to a power surge (we had no surge protector on the appliance). His price for repair was $465.00. We opted to go online for the part and found it for $165.00 through PartSelect.com. It was a very simple procedure of removing the old and installing the new. A few turns with the nut driver to uncover the part, a few tugs with the pliers to disconnect and voila!.. The fridge was back to cooling in no time.

Removed the broken slide (two screws) replaced with the new part

I tried to quite the noisey evap motor with special liquid motor grease from Radio Shack. It did not work, so I ordered the evap motor. My freezer motor was wired slightly different than the motor I received. The replacement motor had a male plug attached to the four wires, the original motor was different, so I cut the wires and spliced them into the original freezer wires (colors were the same). Remounted motor. Works great, and no more groaning motor
Peter

Replaced defrost thermostat along with temp sensor watched the video on this page simple fix

Remove rear plate. Remove fan bracket. Replace fan gaskets, blade and motor. Replace bracket. Replace rear plate. Very simple. Fixed the problem.