Models > EIMGD55IIW2

EIMGD55IIW2 Electrolux Dryer - Overview

Sections of the EIMGD55IIW2

[Viewing 7 of 7]

Manuals & Care Guides for EIMGD55IIW2

Click to download
Keep searches simple, eg. "belt" or "pump".
Belt – Part Number: 134719300
Belt
★★★★★
★★★★★
(3)
PartSelect #: PS2349294
Manufacturer #: 134719300
$76.57
  In Stock
Order within the next 3 hrs and your part ships today!
High Temperature Adhesive – Part Number: 5308027429
High Temperature Adhesive
★★★★★
★★★★★
(1)
PartSelect #: PS474458
Manufacturer #: 5308027429
Used for installing felt and rubber seals on dryers.
$68.93
  In Stock
Order within the next 3 hrs and your part ships today!
Lint Filter – Part Number: 134793600
Lint Filter
★★★★★
★★★★★
(6)
PartSelect #: PS2349312
Manufacturer #: 134793600
$101.33
  In Stock
Order within the next 3 hrs and your part ships today!
Dryer Drum Roller Kit – Part Number: 5304523155
Dryer Drum Roller Kit
PartSelect #: PS12746506
Manufacturer #: 5304523155
INCLUDES 5304523151 SHAFT, 5304523152 ROLLER, 5304523153 NUT, 5304523154 SPACER.
$93.76
  In Stock
Order within the next 3 hrs and your part ships today!
Moisture Sensor – Part Number: 134786100
Moisture Sensor
★★★★★
★★★★★
(2)
PartSelect #: PS2349303
Manufacturer #: 134786100
$97.49
  In Stock
Order within the next 3 hrs and your part ships today!
Thermal Fuse – Part Number: 134711401
Thermal Fuse
★★★★★
★★★★★
(2)
PartSelect #: PS4704883
Manufacturer #: 134711401
$35.25
  In Stock
Order within the next 3 hrs and your part ships today!
SCREW – Part Number: 131168200
SCREW
PartSelect #: PS417085
Manufacturer #: 131168200
Sold individually.
$17.34
  In Stock
Order within the next 3 hrs and your part ships today!
Flame Sensor – Part Number: 5303281135
Flame Sensor
★★★★★
★★★★★
(1)
PartSelect #: PS459818
Manufacturer #: 5303281135
This part senses the flame for heat allowing the gas valve to open.
$38.61
  In Stock
Order within the next 3 hrs and your part ships today!
Thermal Fuse – Part Number: 137539200
Thermal Fuse
★★★★★
★★★★★
(2)
PartSelect #: PS7783961
Manufacturer #: 137539200
$43.34
  In Stock
Order within the next 3 hrs and your part ships today!
MOTOR – Part Number: 5304529782
MOTOR
★★★★★
★★★★★
(1)
PartSelect #: PS16620747
Manufacturer #: 5304529782
This dryer drum drive motor with pulley for drum belt has reverse threads for the blower wheel. This is a genuine OEM part.
$312.02
  In Stock
Order within the next 3 hrs and your part ships today!
IDLER ARM ASSY – Part Number: 134793511
IDLER ARM ASSY
PartSelect #: PS16227173
Manufacturer #: 134793511
This is an authentic idler pulley, which works with dryers.
$58.10
  In Stock
Order within the next 3 hrs and your part ships today!
Blower Wheel and Housing – Part Number: 134690800
Blower Wheel and Housing
PartSelect #: PS2349262
Manufacturer #: 134690800
$213.92
  In Stock
Order within the next 3 hrs and your part ships today!

Questions And Answers for EIMGD55IIW2

Ask our experts a question about this model and we'll get back to you as soon as possible!

1 question answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Idris
May 26, 2022
My dryer comes on buzzes then pauses what's the problem?
For model number EIMGD55IIW2
PartSelect logo
Hello Idris, Thank you for the question. We suggest checking the Door Switch. If the switch can not tell the door is closed it will not start the cycle and it will pause until the door is closed. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1

Common Symptoms of the EIMGD55IIW2

[Viewing 5 of 5]
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing
Show All
Drum Not Spinning
Fixed by
these parts
Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Noisy Dryer
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
Parts Used:
Belt Dryer Drum Roller Kit
  • Philip from Oakland, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
39 of 47 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas flame turns off after a while. No more heat.
Fixed it eventually with part PS470049 ('M' Series Ignition Coil Kit). See separate story.

The flame sensor did not fix it but read on for info on how to replace this part. Before replacing this part, I should have read another posting in a different web site about the ignition coils: if you see a red glow inside the burner unit but the flame does not come on, then the problem is likely to be with the coils, not the flame sensor. However since some users here had solved the problem by replacing the flame sensors, I figured I'd try it. The setting for "More dry, less dry" never worked either so maybe this would fix two problems at once.

This dryer is a stacked front loader sitting on top of our washing machine. Opening the little front door (lower left side) is easy once you figure out that a little screw below needs to be removed. I almost broke the door trying to pull it open. The sensor is attached to the side of the flame area cylinder. It was hard to remove both the screw and the part itself from the slots as it's very springy. In fact when I finally removed it, it dropped to the base of the unit and sparks went flying as one of the electrical clips touched the metal (ground). Tip: first disconnect the electrical lead coming from the back of the unit to the ingnition block and later I used rubber gloves just in case. (I could not access the plug/outlet in the back). I installed the new part easily, though I was confused by the electrical leads: the white wire connects to the lead that has a red plastic dot on the side, but I think that must be a mechanical part and not a (wrong) marking, while the red connects to the other lead. Anyway, I connected it the same way I found it and put it back. Reconnected the other electrical wires and closed the door.

This did not fix the problem which turned out to be with the gas valve coils: as they get old, they turn off the flame when they get hot, even though the dryer keeps on turning. To read how to replace that part, search for comments under part number PS470049 ('M' Series Ignition Coil Kit). I don't know whether replacing the flame sensor is going to fix the "more dry-less dry" function, will have to see. Still, this website is great. Our dryer is a Westinghouse bought in 1991 (almost 20 years old!) and with this fixes it's just like new.
Parts Used:
Flame Sensor
  • Giuseppe from San Francisco, CA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
22 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not ignite
Make Sure Dryer is off and disconnected from power! Also, beware of sharp edges on dryer parts and cabinet.
1) Popped-off top lid with flat-blade screw driver (Insert screw driver in joint between top and front of dryer above door) Spring clips are all that's holding top on in front
2) Unplugged plastic electrical connector located just along the top-right side of dryer
3) Removed one sheet metal screw located about 8" down from top on either side of dryer - total of two screws
4) Pull front of dryer back and pull up at bottom of dryer (Remember that when you replace front you will have to make sure plastic bearing surfaces on dryer tub are centered back in cut-out on front panel. Plastic tabs fit inside the cut-out or else you'll ge a swishing noise when tub rotates)
5) Set front panel to side
6) Flame sensor is located on the left side of the burn chamber sheet metal cover. It has a red and white wire with flat connectors that must be pulled off. Note which color goes to what terminal
7) Unscrew fastener. Note: this screw/fastener needs a non-standard driver to get it out. I have a variety of other drivers beyond phillips/flat types and non of them worked.
8) I ended up using a pair of pliers to just work it out from under the screw. I bent it, as it has a tab that slips in along left bottom edge of burn chamber cover.
9) Finish taking screw out by hand
10) Put new flame sensor in by inserting tab on bottom first. Then, screw in fastener to top of sensor bracket and reconnect wires. White on top and red on bottom terminal.
11) Replace front panel with door by placing in tabs on bottom front of dryer. Again, make sure plastic bearing surfaces are inside of circular flange on front panel
12) Make sure to reconnect plastic cable connector. Note: I added a tie-wrap because it looked like the connector might rub against drum. There are some holes through which you can run the tie-wrap
13) Replace the two sheet-metal screws
14) Push top down so spring clips re-engage with dryer body
Parts Used:
Flame Sensor
  • David from Murrieta, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
17 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!