This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
This washer shock absorber mounting pin is a small but essential fastener that secures the shock absorber to the outer tub of a front-load washing machine. By holding the shock absorber firmly in plac...
This front-load washing machine door boot seal is a flexible rubber component designed to create a watertight barrier between the washer’s door and the inner tub. It plays a critical role in preventin...
The door strike attaches to the door of your front load washer and will activate the door switch once the door is closed. If your washer won’t start or the door won’t close/open properly, you may need...
This washer tub-to-pump hose, often called a coin trap or bellows hose, carries water from the outer tub to the drain pump during drain and spin cycles. Designed with an integrated trap, it captures c...
Have you been facing leaking issues with your washing machine? Our genuine and high-quality Frigidaire Bellows Spring Clamp could be the simple solution you need. Designed for your washing machine's d...
Reduce vibrations and noise during wash and spin cycles with this shock absorber kit, designed to stabilize the washer tub for smooth, quiet operation. Made from durable plastic and rubber components,...
This spring helps keep the rubber seal around your washer’s door in place, stopping leaks and keeping everything running smoothly. If your washer is leaking or the seal looks loose, this part might be...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ben
December 1, 2022
So my washer would not drain and shutdown washer. Unplug for 10 minutes and plug in and panel is operational. I believe this may be a bad drain pump and wanted to know your thoughts concerning problem
For model number EIFLW55HMB0
Hello Ben, thank you for contacting us. You suspected the right part, the issue is most probably caused by a shorted drain pump, part number PS2342436. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
Washes fine then it's done saye no water a cloths are wet put on spin works fine
For model number EIFLW55HMB0
Hi Tom, Thank you for reaching out. If the washer displays "no water" after a wash cycle, it can be caused by a clogged or faulty water inlet valve, a faulty pressure switch, or a faulty electronic control board. We hope this helps, good luck with the repair!
Hi - it sounds like we have something rattling in one of the baffles. How do we unlock our model's baffle to look inside?
For model number EIFLW55HMB0
Hello Aaron, thank you for the question. You may need to insert a small Phillips head screwdriver into the front hole in the baffle and use a mallet to strike the screwdriver from the rear to detach the baffle. We hope this information helps!
Was this helpful?
Thank you for voting!
Aaron
February 27, 2025
Hello - As a follow up to the baffle. What are we feeling for when we insert the screwdriver into the front hole? We tried that route but the baffle would not come off. Could there be a possible other method to remove the baffle from my model?
For model number EIFLW55HMB0
Hi Aaron,
Thank you for your question. There is a screw on the outside of the bracket that holds the vane and nozzle in place. To access the screw, you will need to separate the 2 halves of the outer tub. Once you have unthreaded the screw, you should be able to slide it out of the locking tabs easily. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfectly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
First, I went to the PartSelect website and easily found the part at a reasonable price. I ordered it early on a Wednesday afternoon, and gladly spent the extra $25 to ship it overnight. That evening, PartSelect sent me an email stating that the part had shipped that very day, and - mistakenly - I took that literally. FedEx tracking predicted that the part would arrive on Friday, July 5, which made sense because the 4th was a holiday. But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July. That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping. Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes. But no thanks to PartSelect.
Parts took twice as long to arrive shipped from Utah to Houston, Texas. Once arrived parts were straight forward to install. 1) Open the door by tripping the door strike using yard trimmer line. 2) Turned Power off (unplugged unit) 3) Used needle noses pliers to remove door rubber boot retainer 4) Folded right-side of rubber in to removed switch assembly 5) Used Phillips screwdriver to remove switch assembly screws, navigated damaged switch part forward then disconnected line. 6) Connected new switch to line, navigate part back into washer and screwed back in. 7) Repositioned door rubber boot and reattached door boot retainer wire with hands and needle noose pliers. 8) Replaced door strike using Phillips screw driver. 9) Re-plugged washer power to outlet, closed door and ran a test cycle. All good!
