EHS342-OF (EHS3420OF) Caloric Cooktop - Instructions

Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.

I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.

I had already removed the old hinges by removing the screws/bolts and removing the broken hinges from the back side through the drawer below the oven that I had already removed. Took the new hinges and screwed the two metal screws into the top hole on the new hinges after placing hinge in vise, one screw on each then removed them and placed them to the side. Determined the right tap from my tap set, and then tapped the bottom two holes on the new hinges, one on each. Placed the bolts that came with the new hinges into the holes I had just tapped, screw them in, then I removed them and placed to the side. Took hinges and bolts / screws to the oven, inserted hinges in through the drawer that I had removed up to each side where hinges would come back out to the front of the oven. Placed screws / bolts one at a time through oven door frame into the hinge on the back side, and then threaded them into the hinges and tightened. Replaced oven door onto new hinges and checked for correct operation. Door works like new.

The repair was simple, two screws and plug in and it was done.

Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML

burner was shorting out replaced part works great

1. waited unsuccessfully for heat (one hour) 2. realized the bottom element wasn't working (one minute) 3. found part on-line from pictures (five minutes) 4. ordered part (one minute) 5. received part (36 hours) 6. installed part (five minutes) 7. "THAT'S how you fix the oven" look to husband (1-2 years)

loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.

I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were 2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!

After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good directions.

by myself

I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.

Description of the element indicated that it would work for the oven burner. However, it obviously was meant for the broiler element. I had to remove the thin metal piece with the attachment holes in it (the holes didn't match the holes in the back of the oven). To install I had to drill two holes in the remaining attachment flange to match the holes on the back of the oven. Then I made three metal supports out of sheet metal to hold the element up approximately 1 1/2" off of the bottom of the oven. Just thankful to find one that I could make work. Oven works fine now. LF

It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.

The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase...parts arrived very timely...J. Iriwn